- 您现在的位置：买卖IC网 > PDF目录80532 > MPC5200VR466BR2 (FREESCALE SEMICONDUCTOR INC) 466 MHz, MICROPROCESSOR, PBGA272 PDF资料下载
参数资料
| 型号： | MPC5200VR466BR2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 466 MHz, MICROPROCESSOR, PBGA272 |
| 封装： | 27 X 27 MM, 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, BGA-272 |
| 文件页数： | 68/80页 |
| 文件大小： | 788K |
| 代理商： | MPC5200VR466BR2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
MPC5200B Data Sheet, Rev. 0.6
System Design Information
Freescale Semiconductor
70
5.1.2
Power Down Sequence
If VDD_CORE/PLL_AVDD are powered down first, then sense circuits in the I/O pads will cause all
output drivers to be in a high impedance state. There is no limit on how long after VDD_CORE and
PLL_AVDD power down before VDD_IO or VDD_IO_MEM must power down. VDD_CORE should not
lag VDD_IO, VDD_IO_MEM, or PLL_AVDD going low by more than 0.5V during power down or there
will be undesired high current in the ESD protection diodes. There are no requirements for the fall times
of the power supplies.
The recommended power down sequence is as follows:
Drop VDD_CORE/PLL_AVDD to 0V.
Drop VDD_IO/VDD_IO_MEM supplies.
5.2
System and CPU Core AVDD Power Supply Filtering
Each of the independent PLL power supplies require filtering external to the device. The following
drawing is a recommendation for the required filter circuit.
Figure 52. Power Supply Filtering
5.3
Pull-up/Pull-down Resistor Requirements
The MPC5200B requires external pull-up or pull-down resistors on certain pins.
5.3.1
Pull-down Resistor Requirements for TEST pins
The MPC5200B requires pull-down resistors on the test pins TEST_MODE_0, TEST_MODE_1,
TEST_SEL_1.
5.3.2
Pull-up Requirements for the PCI Control Lines
If the PCI interface is NOT used (and internally disabled) the PCI control pins must be terminated as
indicated by the PCI Local Bus specification [4]. This is also required for MOST/Graphics and Large Flash
Mode.
PCI control signals always require pull-up resistors on the motherboard (not the expansion board) to
ensure that they contain stable values when no agent is actively driving the bus. This includes
AVDD device pin
Power
Supply
source
< 1
10
200-400 pF
10
F
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8250ACVVIHBX | 32-BIT, 200 MHz, RISC PROCESSOR, PBGA480 |
| MC9S12XDT256MFU | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 |
| MAC7131MVF50R2 | 32-BIT, FLASH, 50 MHz, MICROCONTROLLER, PBGA208 |
| MC68L11E0FNE2 | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| MC908QY2MDWR2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC52100J | 功能描述:厚膜电阻器 - 透孔 RoHS:否 制造商:Caddock 电阻:27 kOhms 容差:1 % 功率额定值:8 W 温度系数:50 PPM / C 系列:MS 端接类型:Axial 电压额定值:2 kV 工作温度范围:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封装:Bulk |
| MPC52100J | 制造商:TE Connectivity 功能描述:RESISTOR 5W 10R |
| MPC52100J | 制造商:TE Connectivity 功能描述:RESISTOR THICK FILM 10OHM 5W 5% 制造商:TE Connectivity 功能描述:RESISTOR, THICK FILM, 10 OHM, 5W, 5% |
| MPC52101J | 功能描述:厚膜电阻器 - 透孔 MPC5 100R 5% RoHS:否 制造商:Caddock 电阻:27 kOhms 容差:1 % 功率额定值:8 W 温度系数:50 PPM / C 系列:MS 端接类型:Axial 电压额定值:2 kV 工作温度范围:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封装:Bulk |
| MPC52101J | 制造商:TE Connectivity 功能描述:RESISTOR 5W 100R |
发布紧急采购，3分钟左右您将得到回复。