- 您现在的位置：买卖IC网 > PDF目录22101 > NCP1027P065G (ON Semiconductor)IC SWIT PWM PROG CM OVP HV 8DIP PDF资料下载
参数资料
| 型号： | NCP1027P065G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/30页 |
| 文件大小： | 0K |
| 描述： | IC SWIT PWM PROG CM OVP HV 8DIP |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 58.5kHz ~ 71.5kHz |
| 输入电压： | 7.9 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 25W |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | NCP1027P065GOS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
NCP1027
APPLICATION INFORMATION
Introduction
The NCP1027 offers a complete current-mode control
solution and enhances the NCP101X series. The
component integrates everything needed to build a rugged
and low-cost Switch-Mode Power Supply (SMPS)
featuring low standby power.
? Current-Mode Operation: The controller uses a
current-mode control architecture, which, together
with an adjustable ramp compensation circuitry,
ensures efficient and stable continuous or
? Fail-Safe Optocoupler/Overvoltage Protection: As
the auxiliary winding is connected to the V CC pin, an
internal active clamp connected between V CC and
ground limits the supply dynamics to 8.7 V. In case
the current injected in this clamp exceeds a level of
6.0 mA (minimum), the controller immediately stops
switching and waits a full timer period before
attempting to restart. If the default is gone, the
controller resumes operation. If the default is still
there, e.g. a broken optocoupler, the controller protects
discontinuous conduction designs.
? 700 V–5.8 W Power Switch Circuit: Due to
ON Semiconductor Very High Voltage Integrated
Circuit technology, the circuit hosts a high-voltage
power switch circuit featuring a 5.8 W R DS(on) – T J =
25 ° C. This value lets the designer build a 15 W
power supply operated on universal mains as
long as sufficient copper area exists to lower the
junction-to-ambient thermal resistance. An internal
current source delivers the startup current, necessary
to crank the power supply.
? Short-Cir cuit Protection: By permanently
monitoring the feedback line activity, the circuit is
able to detect the presence of a short-circuit,
immediately reducing the output power for a total
system protection. A 55 ms timer is started as soon as
the feedback pin asks for the maximum peak current.
At the end of this timer, if the fault is still present,
then the device enters a safe, auto-recovery burst
mode, affected by a fixed 440 ms recurrence. Once the
short has disappeared, the controller resumes and goes
back to normal operation. The timer duration is fully
independent from the V CC capacitor value.
? Over Power Protection: A possibility exists to reduce
the maximum output power capability in high line
conditions. A simple two resistor network wired to the
bulk capacitor will program the maximum current
reduction for a given input voltage (down to 20% of
the maximum peak current).
?
?
?
?
?
the load through a safe burst mode.
Brown-Out Input: A fraction of the input voltage
appears on pin 3, due to a resistive divider. If the
mains drops below a level adjusted by this resistive
divider, the circuit does not switch. As soon as the
mains goes back within its normal range, the device
resumes operation and operates normally. By adjusting
the bridge resistors, it becomes possible to set the
brown-out levels (on and off) independently.
Latchoff: Pin 3 also welcomes a comparator who
offers a way to fully latch the controller. If an external
event (e.g. an overtemperature) brings the brown-out
pin above 3.5 V, the circuit stays permanently off
until the user cycles its V CC down, for instance by
unplugging the converter from the mains outlet.
Frequency Jittering: The internal clock receives a
low frequency modulation which helps smoothing the
power supply EMI signature.
Soft-Start: A 1.0 ms soft-start ensures a smooth
startup sequence, reducing output overshoots.
Skip Cycle: If SMPS naturally exhibit a good
efficiency at nominal load, they begin to be less
efficient when the output power demand diminishes.
By skipping unneeded switching cycles, the NCP1027
drastically reduces the power wasted during light load
conditions. Experiments carried over the 5.0 V/2.0 A
demonstration board reveal a standby power at
no-load and 265 Vac of 85 mW and an efficiency for
500 mW output power of 64% at 230 Vac.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| ISL61851LIBZ-T | IC USB PWR CTRLR DUAL 8SOIC |
| AP130-20WL-7 | IC REG LDO 2V .3A SC59-3 |
| S1BB-13-F | RECTIFIER GPP 100V 1A SMD |
| TAP155M025CCS | CAP TANT 1.5UF 25V 20% RADIAL |
| VI-23N-EV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1027P100G | 功能描述:交流/直流开关转换器 PWM Current Mode Controller RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1027PO65G | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
| NCP1028 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Controllers |
| NCP1028LEDGEVB | 功能描述:电源管理IC开发工具 720MA 18V LED DRIVER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1028P065G | 功能描述:电流型 PWM 控制器 NCP1028 65 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。