- 您现在的位置：买卖IC网 > PDF目录22101 > NCP1027P065G (ON Semiconductor)IC SWIT PWM PROG CM OVP HV 8DIP PDF资料下载
参数资料
| 型号： | NCP1027P065G |
| 厂商： | ON Semiconductor |
| 文件页数： | 20/30页 |
| 文件大小： | 0K |
| 描述： | IC SWIT PWM PROG CM OVP HV 8DIP |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 58.5kHz ~ 71.5kHz |
| 输入电压： | 7.9 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 25W |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | NCP1027P065GOS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
NCP1027
20- 8.7 v Rlimit v 12- 8 , that is to say : 1.8 k W t R limit
t 4 k W .
Plugging the values in Equation 3 gives the limits within
which R limit shall be selected:
6m 1m
If we design a 65 kHz power supply delivering 12 V, then
the ratio between auxiliary and power must be: 12/20 = 0.6.
The OVP latch will activate when the clamp current
exceeds 6.0 mA. This will occur when Vauxiliary grows up
to:
1. 8.7 + 1.8 k (6 m + 1.8 m) ≈ 23 V for the first
boundary ( R limit = 1.8 k W ).
2. 8.7 + 4 k (6 m + 1.8 m) ≈ 40 V for the second
boundary ( R limit = 4.0 k W ).
Due to a 0.6 ratio between the auxiliary V CC and the
power winding, the auxiliary OVP will be seen as a lower
overshoot on the real output:
1. 23 0.6 ≈ 13.8 V
2. 40 0.6 ≈ 24 V
As one can see, tweaking the R limit value will allow the
selection of a given overvoltage output level. Theoretically
predicting the auxiliary drop from nominal to standby is an
almost impossible exercise since many parameters are
involved, including the converter time constants. Fine
tuning of R limit thus requires a few iterations and
experiments on a breadboard to check the auxiliary voltage
variations but also the output voltage excursion in fault.
Once properly adjusted, the fail-safe protection will
preclude any lethal voltage runaways in case a problem
would occur in the feedback loop.
> 30 ms
Figure 35. The burst frequency becomes so low
that it is difficult to keep an adequate level on the
auxiliary V CC .
Figure 36 describes the main signal variations when the
part operates in auto-recovery OVP.
Figure 36. If the V CC current exceeds a certain threshold, an auto-recovery protection is
activated and protects the design.
http://onsemi.com
20
相关PDF资料 |
PDF描述 |
|---|---|
| ISL61851LIBZ-T | IC USB PWR CTRLR DUAL 8SOIC |
| AP130-20WL-7 | IC REG LDO 2V .3A SC59-3 |
| S1BB-13-F | RECTIFIER GPP 100V 1A SMD |
| TAP155M025CCS | CAP TANT 1.5UF 25V 20% RADIAL |
| VI-23N-EV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1027P100G | 功能描述:交流/直流开关转换器 PWM Current Mode Controller RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1027PO65G | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
| NCP1028 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Controllers |
| NCP1028LEDGEVB | 功能描述:电源管理IC开发工具 720MA 18V LED DRIVER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1028P065G | 功能描述:电流型 PWM 控制器 NCP1028 65 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。