- 您现在的位置：买卖IC网 > PDF目录22101 > NCP1027P065G (ON Semiconductor)IC SWIT PWM PROG CM OVP HV 8DIP PDF资料下载
参数资料
| 型号： | NCP1027P065G |
| 厂商： | ON Semiconductor |
| 文件页数： | 27/30页 |
| 文件大小： | 0K |
| 描述： | IC SWIT PWM PROG CM OVP HV 8DIP |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 58.5kHz ~ 71.5kHz |
| 输入电压： | 7.9 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 25W |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | NCP1027P065GOS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页
NCP1027
clamp is usually selected 50-80 V above the reflected
Power Dissipation and Heatsinking
value N
(V out + V f ). The diode needs to be a fast one and
The NCP1027 hosting a power switch circuit and a
thus evacuate is: P max +
Tj max - Tamb max
an MUR160 represents a good choice. One major
drawback of the RCD network lies in its dependency upon
the peak current. Worse case occurs when I peak and V in are
maximum and V out is close to reach the steady-state value.
Figure 47c: This option is probably the most expensive
of all three but it offers the best protection degree. If you
need a very precise clamping level, you must implement a
Zener diode or a TVS. There are little technology
differences behind a standard Zener diode and a TVS.
However, the die area is far bigger for a transient suppressor
than that of Zener. A 5.0 W Zener diode, like the 1N5388B,
will accept 180 W peak power if it lasts less than 8.3 ms.
If the peak current in the worse case (e.g. when the PWM
circuit maximum current limit works) multiplied by the
nominal Zener voltage exceeds these 180 W, then the diode
will be destroyed when the supply experiences overloads.
A transient suppressor like the P6KE200 still dissipates
5.0 W of continuous power, but is able to accept surges up
to 600 W @ 1.0 ms. Select the Zener or TVS clamping
level between 40 to 80 V above the reflected output voltage
controller, it is mandatory to properly manage the heat
generated by losses. If no precaution is taken, risks exist to
trigger the internal thermal shutdown (TSD). To help
dissipating the heat, the PCB designer must foresee large
copper areas around the PDI7 package. When surrounded
by a surface greater than 1.0 cm @ of 35 m m copper, it
becomes possible to drop the thermal resistance
junction-to-ambient, R q JA down to 75 ° C/W and thus
dissipate more power. The maximum power the device can
(eq. 22)
R q JA
which gives around 930 mW for an ambient of 50 ° C and a
maximum junction of 120 ° C. The losses inherent to the
switch circuit R DS(on) can be theoretically evaluated, but
the final prototype evaluation must include board
measurements to confirm that the junction temperature
stays within safe limits. Figure 48 gives a possible layout
to help dropping the thermal resistance. When measured on
a 70 m m (2 oz.) copper thickness PCB, we obtained a
thermal resistance of 75 ° C/W.
when the supply is heavily loaded.
Figure 48. A possible PCB arrangement to reduce the thermal resistance
junction-to-ambient.
When routing the printed circuit, it is important to keep
high impedance line very short, like the brown-out signal
and the OPP input if used.
Application Diagram
Figure 49 displays the final application schematic. The
output uses a TLV431 whose low bias current represents an
advantage for low standby power switch mode supplies.
The secondary side features an additional LC filter needed
to remove unwanted spikes, although less problematic than
in DCM operation. On the primary side, a resistive network
senses the input bulk voltage and prevents the controller
from turning on for input voltages below 100 Vdc. The
auxiliary winding delivers 20 V nominal and thus offers
comfortable margin when the converter enters standby. As
we do not use any OPP, pin 7 goes to ground and offers
extended possibility to layout more copper area.
http://onsemi.com
27
相关PDF资料 |
PDF描述 |
|---|---|
| ISL61851LIBZ-T | IC USB PWR CTRLR DUAL 8SOIC |
| AP130-20WL-7 | IC REG LDO 2V .3A SC59-3 |
| S1BB-13-F | RECTIFIER GPP 100V 1A SMD |
| TAP155M025CCS | CAP TANT 1.5UF 25V 20% RADIAL |
| VI-23N-EV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1027P100G | 功能描述:交流/直流开关转换器 PWM Current Mode Controller RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1027PO65G | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
| NCP1028 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Controllers |
| NCP1028LEDGEVB | 功能描述:电源管理IC开发工具 720MA 18V LED DRIVER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1028P065G | 功能描述:电流型 PWM 控制器 NCP1028 65 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。