参数资料
| 型号： | NCP1650EVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 22/31页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL NCP1650 PFC CTLR |
| 设计资源： | NCP1650EVB Schematic NCP1650EVB Bill of Materials NCP1650EVB Test Procedure NCP1650EVB Gerber Zip |
| 标准包装： | 1 |
| 主要目的： | 电源管理，功率因数校正 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | NCP1650 |
| 已供物品： | 板 |
| 其它名称： | NCP1650EVB-ND NCP1650EVBOS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
NCP1650
Comparator monitors the output voltage and will shutdown
operation of the PWM circuit if the output voltage exceeds
8% above the normal regulation level. The Overshoot
Comparator signal is fed into the second Set input to the
latch.
AC Reference Buffer
The AC reference buffer converts the voltage generated
by the AC error amplifier to be converted into a current to
be summed with the ramp compensation signal and the
instantaneous current signal.
The buffer amplifier, converts the input voltage to a
current by creating a current equal to the voltage difference
between the AC error amplifier output and the 2.9 volt
reference dropped across the 14 k Ω resistor. The bipolar
transistor level shifts the voltage and maintains the proper
current into the current mirror. The current mirror has a 1:2
ratio and delivers the output current to the PWM input. This
current is summed with the currents of the ramp
compensation signal and the instantaneous current signal to
determine the turn--off point in the switching cycle.
Soft--Start Circuit
The AC error amplifier has been configured such that a
AC
Comp
3
AC
ERROR
AMP
2.9 V
+
--
+
--
CURRENT
MIRROR
i 1
14 k
2 X i 1
16 k
PWM,
Ramp
Comp
Current
Sense
Amp
low output level will cause the output duty cycle to go to
zero. This will have the effect of soft--starting the unit at
turn--on, since the output is coupled to ground through a
capacitor.
There will be an initial offset of the output voltage due to
the output current and the resistor at pin 3. For example, if
the output is saturated in the high state at turn on, it will
source 50 m A. If pin 3 is terminated with a 2.2 k Ω resistor
and a 0.01 F capacitor, the initial step will be:
50 m A × 2.2 k = 0.11 volts
and the rate of rise will be:
Unity Gain Amplifier
Figure 39. AC Reference Buffer Schematic
The buffer ’s transfer function is:
50 m A ∕ 0.01 m F = 5 mv ∕ m s
or, 560 m s until the output is at 2.9 volts, which corresponds
to full duty cycle.
An external soft--start circuit can be added, as shown in
Figure 29, if additional time is desired.
iout = (2.9 V ? Vac) ∕ 7 k
http://onsemi.com
22
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1652L48VGEVB | BOARD EVAL 100W 48V NCP1652 PFC |
| NCP1653EVB | BOARD EVAL FOR NCP1653 |
| NCP2993FCT2GEVB | BOARD EVAL NCP2993 AUDIO PWR AMP |
| NCP345SNT1G | IC DETECTOR OVER VOLTAGE 5TSOP |
| NCP346SN2T1G | IC DETECTOR OVER VOLTAGE 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1651DR2 | 功能描述:功率因数校正 IC Single Stage PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1651DR2G | 功能描述:功率因数校正 IC Single Stage PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1652ADR2G | 功能描述:功率因数校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1652DR2G | 功能描述:功率因数校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1652DWR2G | 功能描述:功率因数校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。