参数资料
型号: P89V52X2FBD,157
厂商: NXP Semiconductors
文件页数: 17/57页
文件大小: 0K
描述: IC 80C51 MCU FLASH 8K 44-LQFP
产品培训模块: Migrating from 8/16-Bit MCUs to 32-Bit ARMs
标准包装: 800
系列: 89V
核心处理器: 8051
芯体尺寸: 8-位
速度: 40MHz
连通性: UART/USART
外围设备: POR
输入/输出数: 32
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
EEPROM 大小: 192 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LQFP
包装: 托盘
配用: 622-1017-ND - BOARD 44-ZIF PLCC SOCKET
622-1012-ND - BOARD FOR P89V52X2 44-TQFP
622-1008-ND - BOARD FOR LPC9103 10-HVSON
其它名称: 568-4250
935282529157
P89V52X2FBD
P89V52X2_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 4 May 2009
24 of 57
NXP Semiconductors
P89V52X2
80C51 with 256 B RAM, 192 B data EEPROM
used as the UART transmit baud rate generator. RCLK has the same effect for the UART
receive baud rate. With these two bits, the serial port can have different receive and
transmit baud rates – Timer 1 or Timer 2.
Figure 17 shows Timer 2 in baud rate generator mode:
The baud rate generation mode is like the auto-reload mode, when a rollover in TH2
causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and
RCAP2L, which are preset by software.
The baud rates in modes 1 and 3 are determined by Timer 2’s overow rate given below:
Modes 1 and 3 Baud Rates = Timer 2 Overow Rate/16
The timer can be congured for either ‘timer’ or ‘counter’ operation. In many applications,
it is congured for ‘timer' operation (C/T2 = 0). Timer operation is different for Timer 2
when it is being used as a baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e., 1
6 the oscillator
frequency). As a baud rate generator, it increments at the oscillator frequency. Thus the
baud rate formula is as follows:
Modes 1 and 3 Baud Rates =
(3)
Where: (RCAP2H, RCAP2L) = The content of RCAP2H and RCAP2L taken as a 16-bit
unsigned integer.
The Timer 2 as a baud rate generator mode is valid only if RCLK and/or TCLK = 1 in
T2CON register. Note that a rollover in TH2 does not set TF2, and will not generate an
interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the
baud rate generator mode. Also if the EXEN2 (T2 external enable ag) is set, a 1-to-0
transition in T2EX (Timer/counter 2 trigger input) will set EXF2 (T2 external ag) but will
not cause a reload from (RCAP2H, RCAP2L) to (TH2, TL2). Therefore when Timer 2 is in
use as a baud rate generator, T2EX can be used as an additional external interrupt, if
needed.
Fig 17. Timer 2 in Baud Rate Generator mode
002aaa526
TX/RX baud rate
timer 2
interrupt
OSC
÷2
T2 pin
C/T2 = 0
C/T2 = 1
TL2
(8-bits)
TH2
(8-bits)
control
TR2
EXF2
RCAP2L RCAP2H
control
EXEN2
transition
detector
T2EX pin
reload
OscillatorFrequency
16
65536
RCAP2H RCAP2L
,
()
()
×
()
------------------------------------------------------------------------------------------------
相关PDF资料
PDF描述
P89V52X2FA,512 IC 80C51 MCU FLASH 8K 44-PLCC
VJ2225Y104KBLAT4X CAP CER 0.1UF 630V 10% X7R 2225
LPC2292FET144/G,55 IC ARM7 MCU FLASH 256K 144TFBGA
VI-JWM-IY-F4 CONVERTER MOD DC/DC 10V 50W
VI-JWL-IY-F3 CONVERTER MOD DC/DC 28V 50W
相关代理商/技术参数
参数描述
P89V52X2FN 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 low power 8 kB flash microcontroller with 256 B RAM, 192 B data EEPROM
P89V52X2FN,112 功能描述:8位微控制器 -MCU 80C51 8K FL / 256 RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89V660 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V660_08 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V660_0811 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI