参数资料
型号: P89V52X2FBD,157
厂商: NXP Semiconductors
文件页数: 28/57页
文件大小: 0K
描述: IC 80C51 MCU FLASH 8K 44-LQFP
产品培训模块: Migrating from 8/16-Bit MCUs to 32-Bit ARMs
标准包装: 800
系列: 89V
核心处理器: 8051
芯体尺寸: 8-位
速度: 40MHz
连通性: UART/USART
外围设备: POR
输入/输出数: 32
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
EEPROM 大小: 192 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LQFP
包装: 托盘
配用: 622-1017-ND - BOARD 44-ZIF PLCC SOCKET
622-1012-ND - BOARD FOR P89V52X2 44-TQFP
622-1008-ND - BOARD FOR LPC9103 10-HVSON
其它名称: 568-4250
935282529157
P89V52X2FBD
P89V52X2_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 4 May 2009
34 of 57
NXP Semiconductors
P89V52X2
80C51 with 256 B RAM, 192 B data EEPROM
The data EEPROM must be mapped into the code memory address space in order to
read, erase, or program the data EEPROM. The memory is read using the MOVC
instruction.
6.13.1 Features
ICP with industry-standard commercial programmers
IAP-Lite allows individual and multiple bytes of data EEPROM to be programmed
under control of the end application.
Programming and erase over the full operating voltage range
Programming/Erase using ICP or IAP-Lite
Program or erases requires 2 ms, 4 ms, or 6 ms, depending on the operation
Programmable security for the data in each page
> 100000 typical erase/program cycles for each byte
Data EEPROM mapped into code space for quick MOVC reading
6.13.2 Register interface
Erasing, programming, and mapping operations are performed in the application under
the control of the microcontroller’s rmware using four SFRs and an internal 64-byte ‘page
register’. These SFRs are:
FMCON (Flash Control Register). When read, this is the status register. When written,
this is a command register. Note that the status bits are cleared to logic 0s when the
command is written.
FMADRL, FMADRH (Flash memory address low, Flash memory address high). Used
to specify the byte address within the page register or specify the page within user
code memory (for programming, erase, and reading the data EEPROM is mapped
into the user address space (see Table 32).
FMDATA (Flash Data Register). Accepts data to be loaded into the page register.
Data is read by mapping the data EEPROM into the code memory space and using the
MOVC instruction.
6.13.3 Mapping the data EEPROM into code space
In order to read, erase, or program the data EEPROM must be mapped into the code
memory address space. This is accomplished by writing the MAP command (09H) to
FMCON. The data EEPROM may be unmapped by writing the UNMAP command (0AH)
to FMCON. The mapping of the data EEPROM pages into code memory space is shown
6.13.4 Reading the data EEPROM
Reading the data EEPROM can be achieved by performing the following sequence:
Table 32.
Data EEPROM page addresses
Data EEPROM page
Start address End address
0
FF00H
FF3FH
1
FF40H
FF7FH
2
FF80H
FFBFH
相关PDF资料
PDF描述
P89V52X2FA,512 IC 80C51 MCU FLASH 8K 44-PLCC
VJ2225Y104KBLAT4X CAP CER 0.1UF 630V 10% X7R 2225
LPC2292FET144/G,55 IC ARM7 MCU FLASH 256K 144TFBGA
VI-JWM-IY-F4 CONVERTER MOD DC/DC 10V 50W
VI-JWL-IY-F3 CONVERTER MOD DC/DC 28V 50W
相关代理商/技术参数
参数描述
P89V52X2FN 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 low power 8 kB flash microcontroller with 256 B RAM, 192 B data EEPROM
P89V52X2FN,112 功能描述:8位微控制器 -MCU 80C51 8K FL / 256 RM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89V660 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V660_08 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI
P89V660_0811 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 16 kB/32 kB/64 kB flash microcontroller with 512 B/1 kB/2 kB RAM, dual I2C-bus, SPI