参数资料
型号: PIC12F1840T-I/MF
厂商: Microchip Technology
文件页数: 73/122页
文件大小: 0K
描述: MCU 7KB FLASH 256B RAM XLP 8DFN
标准包装: 3,300
系列: PIC® XLP™ 12F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,LIN,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 5
程序存储器容量: 7KB(4K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.3 V ~ 5.5 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 8-VDFN 裸露焊盘
包装: 带卷 (TR)
PIC12(L)F1840
DS41441B-page 54
Preliminary
2011 Microchip Technology Inc.
5.2.2.6
32 MHz Internal Oscillator
Frequency Selection
The Internal Oscillator Block can be used with the 4X
PLL associated with the External Oscillator Block to
produce a 32 MHz internal system clock source. The
following settings are required to use the 32 MHz inter-
nal clock source:
The FOSC bits in Configuration Word 1 must be
set to use the INTOSC source as the device sys-
tem clock (FOSC<2:0> = 100).
The SCS bits in the OSCCON register must be
cleared to use the clock determined by
FOSC<2:0> in Configuration Word 1
(SCS<1:0> = 00).
The IRCF bits in the OSCCON register must be
set to the 8 MHz HFINTOSC set to use
(IRCF<3:0> = 1110).
The SPLLEN bit in the OSCCON register must be
set to enable the 4xPLL, or the PLLEN bit of the
Configuration Word 2 must be programmed to a
‘1’.
The 4xPLL is not available for use with the internal
oscillator when the SCS bits of the OSCCON register
are set to ‘1x’. The SCS bits must be set to ‘00’ to use
the 4xPLL with the internal oscillator.
5.2.2.7
Internal Oscillator Clock Switch
Timing
When switching between the HFINTOSC, MFINTOSC
and the LFINTOSC, the new oscillator may already be
shut down to save power (see Figure 5-7). If this is the
case, there is a delay after the IRCF<3:0> bits of the
OSCCON register are modified before the frequency
selection takes place. The OSCSTAT register will
reflect the current active status of the HFINTOSC,
MFINTOSC and LFINTOSC oscillators. The sequence
of a frequency selection is as follows:
1.
IRCF<3:0> bits of the OSCCON register are
modified.
2.
If the new clock is shut down, a clock start-up
delay is started.
3.
Clock switch circuitry waits for a falling edge of
the current clock.
4.
The current clock is held low and the clock
switch circuitry waits for a rising edge in the new
clock.
5.
The new clock is now active.
6.
The OSCSTAT register is updated as required.
7.
Clock switch is complete.
See Figure 5-7 for more details.
If the internal oscillator speed is switched between two
clocks of the same source, there is no start-up delay
before the new frequency is selected. Clock switching
time delays are shown in Table 5-1.
Start-up delay specifications are located in the
oscillator
tables
of
Note:
When using the PLLEN bit of the
Configuration Word 2, the 4xPLL cannot
be disabled by software and the 8 MHz
HFINTOSC option will no longer be
available.
相关PDF资料
PDF描述
VE-J3W-IW-F1 CONVERTER MOD DC/DC 5.5V 100W
PIC16LF1903T-I/SS MCU 7KB FLASH 256B RAM 28SSOP
VE-J3V-IW-F1 CONVERTER MOD DC/DC 5.8V 100W
PIC16LF1902-E/SO MCU 3.5KB FLASH 128B RAM 28SOIC
VE-J3P-IW-F3 CONVERTER MOD DC/DC 13.8V 100W
相关代理商/技术参数
参数描述
PIC12F505 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers
PIC12F505TE/MC 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers
PIC12F505TE/MG 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers
PIC12F505TE/MS 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers
PIC12F505TE/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers