- 您现在的位置：买卖IC网 > PDF目录11610 > PIC12F1840T-I/MF (Microchip Technology)MCU 7KB FLASH 256B RAM XLP 8DFN PDF资料下载
参数资料
| 型号： | PIC12F1840T-I/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 93/122页 |
| 文件大小： | 0K |
| 描述： | MCU 7KB FLASH 256B RAM XLP 8DFN |
| 标准包装： | 3,300 |
| 系列： | PIC® XLP™ 12F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 32MHz |
| 连通性： | I²C，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 5 |
| 程序存储器容量： | 7KB（4K x 14） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 256 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页
PIC12(L)F1840
DS41441B-page 72
Preliminary
2011 Microchip Technology Inc.
7.3
MCLR
The MCLR is an optional external input that can reset
the device. The MCLR function is controlled by the
MCLRE bit of Configuration Word 1 and the LVP bit of
Configuration Word 2 (Table 7-2).
7.3.1
MCLR ENABLED
When MCLR is enabled and the pin is held low, the
device is held in Reset. The MCLR pin is connected to
VDD through an internal weak pull-up.
The device has a noise filter in the MCLR Reset path.
The filter will detect and ignore small pulses.
7.3.2
MCLR DISABLED
When MCLR is disabled, the pin functions as a general
purpose input and the internal weak pull-up is under
software control. See Section 12.2 “PORTA Registers”
for more information.
7.4
Watchdog Timer (WDT) Reset
The Watchdog Timer generates a Reset if the firmware
does not issue a CLRWDT instruction within the time-out
period. The TO and PD bits in the STATUS register are
changed to indicate the WDT Reset. See Section 10.0
for more information.
7.5
RESET
Instruction
A RESET instruction will cause a device Reset. The RI
bit in the PCON register will be set to ‘0’. See Table 7-4
for default conditions after a RESET instruction has
occurred.
7.6
Stack Overflow/Underflow Reset
The device can reset when the Stack Overflows or
Underflows. The STKOVF or STKUNF bits of the PCON
register indicate the Reset condition. These Resets are
enabled by setting the STVREN bit in Configuration
Word 2. See Section 3.4.2 “Overflow/Underflow
for more information.
7.7
Programming Mode Exit
Upon exit of Programming mode, the device will
behave as if a POR had just occurred.
7.8
Power-Up Timer
The Power-up Timer optionally delays device execution
after a BOR or POR event. This timer is typically used to
allow VDD to stabilize before allowing the device to start
running.
The Power-up Timer is controlled by the PWRTE bit of
Configuration Word 1.
7.9
Start-up Sequence
Upon the release of a POR or BOR, the following must
occur before the device will begin executing:
1.
Power-up Timer runs to completion (if enabled).
2.
Oscillator start-up timer runs to completion (if
required for oscillator source).
3.
MCLR must be released (if enabled).
The total time-out will vary based on oscillator configu-
ration and Power-up Timer configuration. See
for more information.
The Power-up Timer and oscillator start-up timer run
independently of MCLR Reset. If MCLR is kept low long
enough, the Power-up Timer and oscillator start-up
timer will expire. Upon bringing MCLR high, the device
will begin execution immediately (see Figure 7-4). This
is useful for testing purposes or to synchronize more
than one device operating in parallel.
TABLE 7-2:
MCLR CONFIGURATION
MCLRE
LVP
MCLR
00
Disabled
10
Enabled
x1
Enabled
Note:
A Reset does not drive the MCLR pin low.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J3W-IW-F1 | CONVERTER MOD DC/DC 5.5V 100W |
| PIC16LF1903T-I/SS | MCU 7KB FLASH 256B RAM 28SSOP |
| VE-J3V-IW-F1 | CONVERTER MOD DC/DC 5.8V 100W |
| PIC16LF1902-E/SO | MCU 3.5KB FLASH 128B RAM 28SOIC |
| VE-J3P-IW-F3 | CONVERTER MOD DC/DC 13.8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC12F505 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。