- 您现在的位置：买卖IC网 > PDF目录98069 > S1R72105F00A000 SCSI BUS CONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | S1R72105F00A000 |
| 元件分类： | 总线控制器 |
| 英文描述： | SCSI BUS CONTROLLER, PQFP100 |
| 封装： | 0.50 MM PITCH, PLASTIC, QFP15-100 |
| 文件页数： | 63/99页 |
| 文件大小： | 666K |
| 代理商： | S1R72105F00A000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页当前第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
S1R72105 Technical Manual
60
EPSON
Rev.1.0
7.6.3
Command Execution and Change of State
The IC goes through the following three states from the viewpoint of execution of SCSI-type commands:
Disconnected state (D)
Connected state in Initiator mode (I)
Connected state in Target mode (T)
Changes in these states caused by specific commands are as shown in the figure below:
D
WAIT_SCAM_SELECT_COMMAND
SELECT
***
WAIT_SELECT_COMMAND
WAIT_RESELECT
RESELECT
BUSFREE
ASSERT_RST
I
T
Change from I to D takes place implicitly except that by the Assert_RST command.
It means that there is no command that causes such change explicitly. If busfree is found when the next
connection-type command is issued, it is assumed to be the disconnected state and the command is executed.
If busfree is not found, the disconnected state is waited for and the connection-related command is put on hold.
The connection-type command can be executed in the disconnected state. It may be issued in such state.
If it is issued while the SCSI control command is being executed, however, a command error occurs.
A transfer-type command can be executed in the connected state. If it is issued in the disconnected state, a
command error occurs.
Both connection- and transfer-type commands can be executed when the IC is in the condition where no SCSI
control command is being executed.
If they are issued while SCSI control command is in execution, a command error occurs.
7.7
Others and Cautions in Operation
Operation responding to the selection without the SCSI-1 arbitration phase
The IC operates as mentioned below in response to the selection of only target ID of SCSI-1. Note that there
occurs no (automatic) transition to the message or command phase after selection, as in the usual cases after the
Wait_selection command.
(1) If only a target ID is selected after the Wait_select_cmd command is issued, an IDERR interrupt occurs
and the command is terminated.
The inside is in the condition where connection is complete, though. So message_out/command_out and
other commands can be issued, as in the usual case the selection is made with an initiator/target ID
(except that message_out/command_out is not executed automatically).
(2) If an ID of 3 bits or more is selected, an IDERR interrupt occurs. This distinguishes whether selection of
1 bit is completed or IDERR with an ID of 3 bits or more is selected.
If 1 bit is selected, IDERR and SEL interrupts occur. If ATN is not asserted here, a WOATN interrupt
occurs at the same time.
* The firm is asked to check that the SCSI-1 selection has occurred by observing the SEL interrupt at the
same time when an IDERR interrupt occurs.
Also, issue message_out/command_out manually while observing the state of WOATN interrupt, because
IDERR terminates the Wait_selection command.
相关PDF资料 |
PDF描述 |
|---|---|
| S1R72803F00A100 | 1 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP100 |
| S1R72C05B08 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA121 |
| S1R72C05B10 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA121 |
| S1R72V17B00A | UNIVERSAL SERIAL BUS CONTROLLER, PBGA60 |
| S1R72V18B10 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA121 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S1R72803F00A200 | 功能描述:IC LINK CTRLR 1394 IDE-66 184QFP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| S1R72805F00A2 | 功能描述:IC LINK CTRLR 1394 IDE100 100QFP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| S1R72901F00A | 功能描述:IC LINK CTRLR/PHY 1394 100-QFP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| S1R72901F00A200 | 功能描述:IC PHY CONT 2PORT 1394A 100-QFP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| S1R72C05 | 制造商:EPSON 制造商全称:EPSON 功能描述:Support for control, bulk, interrupt, and isochronous transfers |
发布紧急采购，3分钟左右您将得到回复。