- 您现在的位置：买卖IC网 > PDF目录192295 > S29CD032J1JFAI122 (SPANSION LLC) 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 PDF资料下载
参数资料
| 型号： | S29CD032J1JFAI122 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| 封装： | 13 X 11 MM, 1 MM PITCH, FORTIFIED, BGA-80 |
| 文件页数： | 28/78页 |
| 文件大小： | 1825K |
| 代理商： | S29CD032J1JFAI122 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页
32
S29CD-J & S29CL-J Flash Family
S29CD-J_CL-J_00_B1 September27,2006
Prel imi n ary
After an erase-suspended program operation is complete, the bank returns to the erase-suspend
read mode. The system can determine the status of the program operation using the DQ7, DQ6,
and/or RY/BY# status bits, just as in the standard program operation.
To resume the sector erase operation, the system must write the Erase Resume command. The
bank address of the erase-suspended bank is required when writing this command. Further
writes of the Resume command are ignored. Another Erase Suspend command can be written
after the chip has resumed erasing.
The following are the allowable operations when Erase Suspend is issued under certain
conditions:
For the Busy Sectors, the host system may
Read status
Write the Erase Resume command
For the Non Busy Sectors, the system may
Read data
Program data or write the Suspend/Resume Erase command
8.7.5
Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming op-
eration so that data can read from any non-suspended sector. When the Program Suspend
command is written during a programming process, the device halts the programming operation
and updates the status bits.
After the programming operation has been suspended, the system can read array data from any
non-suspended sector. If a read is needed from the Secured Silicon Sector area, then user must
use the proper command sequences to enter and exit this region. The Sector Erase and Program
Resume Command is ignored if the Secured Silicon sector is enabled.
After the Program Resume command is written, the device reverts to programming. The system
can determine the status of the program operation using the DQ7, DQ6, and/or RY/BY# status
bits, just as in the standard program operation. See Write Operation Status on page 33 for more
information.
The system must write the Program Resume command in order to exit the Program Suspend
mode, and continue the programming operation. Further writes of the Program Resume com-
mand are ignored. Another Program Suspend command can be written after the device has
resumed programming.
The following are the allowable operations when Program Suspend is issued under certain
conditions:
For the Busy Sectors, the host system may write the Program Resume command
For the Non Busy Sectors, the system may read data
8.7.6
Accelerated Program and Erase Operations
Accelerated programming and erasing is enabled through the ACC function. This method is faster
than the standard program command sequences.
The device offers accelerated program/erase operations through the ACC pin. When the system
asserts VHH (12V) on the ACC pin, the device automatically enters the Unlock Bypass mode. The
system may then write the two-cycle Unlock Bypass program command sequence to do acceler-
ated programming. The device uses the higher voltage on the ACC pin to accelerate the
operation. Any sector that is being protected with the WP# pin is still protected during acceler-
ated program or Erase. Removing VHH from the ACC input, upon completion of the embedded
program or erase operation, returns the device to normal operation.
相关PDF资料 |
PDF描述 |
|---|---|
| S29CD032J1MFAN120 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| S29CD032J1MQFN133 | 1M X 32 FLASH 2.7V PROM, 54 ns, PQFP80 |
| S29CL016J0JQFI100 | 512K X 32 FLASH 3.3V PROM, 54 ns, PQFP80 |
| S29CL016J0MFAI113 | 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80 |
| S29CL016J0PQFI102 | 512K X 32 FLASH 3.3V PROM, 54 ns, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29CL016J0JQFM030 | 制造商:Spansion 功能描述:FLASH PARALLEL 3.3V 16MBIT 512KX32 54NS 80PQFP - Trays |
| S29CL016J0JQFM030P | 制造商:Spansion 功能描述:AUTO 3.3V 512KX32 FLASH - Trays |
| S29CL016J0JQFM030U | 制造商:Spansion 功能描述:32M (4MX8/2MX16) 3V REG, MIRRORBIT, TOP, FBGA48, IND - Trays |
| S29CL016J0JQFM03U | 制造商:Spansion 功能描述:32M (4MX8/2MX16) 3V REG, MIRRORBIT, TOP, FBGA48, IND - Trays |
| S29CL016J0MQFM030 | 制造商:Spansion 功能描述: |
发布紧急采购，3分钟左右您将得到回复。