- 您现在的位置：买卖IC网 > PDF目录98078 > SC16C654IA68,512 (NXP SEMICONDUCTORS) 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF资料下载
参数资料
| 型号： | SC16C654IA68,512 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封装： | PLASTIC, MS-018, SOT-188-2, LCC-68 |
| 文件页数： | 52/52页 |
| 文件大小： | 647K |
| 代理商： | SC16C654IA68,512 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页
Philips Semiconductors
SC16C654/654D
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 04 — 19 June 2003
9 of 52
9397 750 11617
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
INTA, INTB,
INTC, INTD
15, 21,
49, 55
6, 12,
37, 43
O
Interrupt A, B, C, D (Active-HIGH). This function is associated with the
16 mode only. These pins provide individual channel interrupts INTA-INTD.
INTA-INTD are enabled when MCR[3] is set to a logic 1, interrupts are enabled
in the interrupt enable register (IER), and when an interrupt condition exists.
Interrupt conditions include: receiver errors, available receiver buffer data,
transmit buffer empty, or when a modem status ag is detected. When the
68 mode is selected, the functions of these pins are re-assigned. 68 mode
functions are described under their respective name/pin headings.
INTSEL
65
-
I
Interrupt Select (Active-HIGH, with internal pull-down). This function is
associated with the 16 mode only. When the 16 mode is selected, this pin can
be used in conjunction with MCR[3] to enable or disable the 3-State interrupts,
INTA-INTD, or override MCR[3] and force continuous interrupts. Interrupt
outputs are enabled continuously by making this pin a logic 1. Making this pin a
logic 0 allows MCR[3] to control the 3-State interrupt output. In this mode,
MCR[3] is set to a logic 1 to enable the 3-State outputs. This pin is disabled in
the 68 mode. Due to pin limitations on the 64-pin packages, this pin is not
available. To cover this limitation, the SC16C654DIB64 version operates in the
continuous interrupt enable mode by bonding this pin to VCC internally. The
SC16C654IB64 operates with MCR[3] control by bonding this pin to GND.
IOR
52
40
I
Input/Output Read strobe (Active-LOW). This function is associated with the
16 mode only. A logic 0 transition on this pin will load the contents of an internal
register dened by address bits A0-A2 onto the SC16C654/654D data bus
(D0-D7) for access by external CPU. This pin is disabled in the 68 mode.
IOW18
9
I
Input/Output Write strobe (Active-LOW). This function is associated with the
16 mode only. A logic 0 transition on this pin will transfer the contents of the
data bus (D0-D7) from the external CPU to an internal register that is dened
by address bits A0-A2. When the 16 mode is selected (PLCC68), this pin
functions as R/W (see denition under R/W).
IRQ
15
-
O
Interrupt Request or Interrupt ‘A’. This function is associated with the
68 mode only. In the 68 mode, interrupts from UART channels A-D are
wire-ORed internally to function as a single IRQ interrupt. This pin transitions to
a logic 0 (if enabled by the interrupt enable register) whenever a UART
channel(s) requires service. Individual channel interrupt status can be
determined by addressing each channel through its associated internal
register, using CS and A3-A4. In the 68 mode, and external pull-up resistor
must be connected between this pin and VCC. The function of this pin changes
to INTA when operating in the 16 mode (see denition under INTA).
NC
21, 49,
52, 54,
55, 65
-
Not connected.
RESET,
RESET
37
27
I
Reset. In the 16 mode, a logic 1 on this pin will reset the internal registers and
all the outputs. The UART transmitter output and the receiver input will be
disabled during reset time. (See Section 7.11 “SC16C654/654D external reset
conditions” for initialization details.) When 16/68 is a logic 0 (68 mode), this pin
functions similarly, bus as an inverted reset interface signal, RESET.
RIA, RIB,
RIC, RID
8, 28,
42, 62
63, 19,
30, 50
I
Ring Indicator (Active-LOW). These inputs are associated with individual
UART channels, A through D. A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt.
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
PLCC68 LQFP64
相关PDF资料 |
PDF描述 |
|---|---|
| SC18005CQ | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP144 |
| SC18IS600IBS,151 | I2C BUS CONTROLLER, PQCC24 |
| SC18IS600IBS | I2C BUS CONTROLLER, PQCC24 |
| SC2200UCL-300 | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC2200UCL-300F | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C654IB64 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C654IB64,128 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C654IB64,151 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C654IB64,157 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C750 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO |
发布紧急采购，3分钟左右您将得到回复。