- 您现在的位置：买卖IC网 > PDF目录98078 > SC16C654IA68,512 (NXP SEMICONDUCTORS) 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF资料下载
参数资料
| 型号： | SC16C654IA68,512 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封装： | PLASTIC, MS-018, SOT-188-2, LCC-68 |
| 文件页数： | 6/52页 |
| 文件大小： | 647K |
| 代理商： | SC16C654IA68,512 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Philips Semiconductors
SC16C654/654D
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 04 — 19 June 2003
14 of 52
9397 750 11617
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
interrupt is generated whenever the Receive Holding Register (RHR) has not been
read following the loading of a character or the receive trigger level has not been
reached. (For a description of this timing, see Section 6.6 “Hardware ow control”.)
6.6 Hardware ow control
When automatic hardware ow control is enabled, the SC16C654/654D monitors the
CTS pin for a remote buffer overow indication and controls the RTS pin for local
buffer overows. Automatic hardware ow control is selected by setting EFR[6] (RTS)
and EFR[7] (CTS) to a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating
a ow control request, ISR[5] will be set to a logic 1 (if enabled via IER[6,7]), and the
SC16C654/654D will suspend TX transmissions as soon as the stop bit of the
character in process is shifted out. Transmission is resumed after the CTS input
returns to a logic 0, indicating more data may be sent.
With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed trigger level. The RTS pin will not be forced to a logic 1
(RTS off), until the receive FIFO reaches the next trigger level. However, the RTS pin
will return to a logic 0 after the data buffer (FIFO) is unloaded to the next trigger level
below the programmed trigger. However, under the above described conditions, the
SC16C654/654D will continue to accept data until the receive FIFO is full.
6.7 Software ow control
When software ow control is enabled, the SC16C654/654D compares one or two
sequential receive data characters with the programmed Xon/Xoff or Xoff1,2
character value(s). If received character(s) match the programmed values, the
SC16C654/654D will halt transmission (TX) as soon as the current character(s) has
completed transmission. When a match occurs, the receive ready (if enabled via Xoff
IER[5]) ags will be set and the interrupt output pin (if receive interrupt is enabled) will
be activated. Following a suspension due to a match of the Xoff characters’ values,
the SC16C654/654D will monitor the receive data stream for a match to the Xon1,2
character value(s). If a match is found, the SC16C654/654D will resume operation
and clear the ags (ISR[4]). The SC16C654/654D offers a special Xon mode via
MCR[5]. The initialized default setting of MCR[5] is a logic 0. In this state, Xoff and
Xon will operate as dened above. Setting MCR[5] to a logic 1 sets a special
operational mode for the Xon function. In this case, Xoff operates normally, however,
transmission (Xon) will resume with the next character received, i.e., a match is
declared simply by the receipt of an incoming (RX) character.
Reset initially sets the contents of the Xon/Xoff 8-bit ow control registers to a logic 0.
Following reset, the user can write any Xon/Xoff value desired for software ow
control. Different conditions can be set to detect Xon/Xoff characters and
Table 6:
RX trigger levels
Selected trigger level
(characters)
INT pin activation
Negate RTS or
send Xoff
(characters)
Assert RTS or
send Xon
(characters)
8
16
0
16
56
7
56
60
15
60
55
相关PDF资料 |
PDF描述 |
|---|---|
| SC18005CQ | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP144 |
| SC18IS600IBS,151 | I2C BUS CONTROLLER, PQCC24 |
| SC18IS600IBS | I2C BUS CONTROLLER, PQCC24 |
| SC2200UCL-300 | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC2200UCL-300F | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C654IB64 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C654IB64,128 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C654IB64,151 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C654IB64,157 | 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C750 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO |
发布紧急采购，3分钟左右您将得到回复。