- 您现在的位置：买卖IC网 > PDF目录98141 > SPAK56F807VF80 (MOTOROLA INC) 16-BIT, 80 MHz, OTHER DSP, PBGA160 PDF资料下载
参数资料
| 型号： | SPAK56F807VF80 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 数字信号处理 |
| 英文描述： | 16-BIT, 80 MHz, OTHER DSP, PBGA160 |
| 封装： | MOLD ARRAY PROCESS, BGA-160 |
| 文件页数： | 42/48页 |
| 文件大小： | 853K |
| 代理商： | SPAK56F807VF80 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页
Electrical Design Considerations
MOTOROLA
DSP56F807 Preliminary Technical Data
47
The junction-to-case thermal resistances quoted in this data sheet are determined using the first definition
on page 46. From a practical standpoint, that value is also suitable for determining the junction temperature
from a case thermocouple reading in forced convection environments. In natural convection, using the
junction-to-case thermal resistance to estimate junction temperature from a thermocouple reading on the
case of the package will estimate a junction temperature slightly hotter than actual. Hence, the new thermal
metric, Thermal Characterization Parameter, or
Ψ
JT, has been defined to be (TJ – TT)/PD. This value gives
a better estimate of the junction temperature in natural convection when using the surface temperature of
the package. Remember that surface temperature readings of packages are subject to significant errors
caused by inadequate attachment of the sensor to the surface and to errors caused by heat loss to the sensor.
The recommended technique is to attach a 40-gauge thermocouple wire and bead to the top center of the
package with thermally conductive epoxy.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct DSP operation:
Provide a low-impedance path from the board power supply to each VDD pin on the DSP, and from
the board ground to each VSS pin.
The minimum bypass requirement is to place six 0.01–0.1
F capacitors positioned as close as
possible to the package supply pins. The recommended bypass configuration is to place one bypass
capacitor on each of the ten VDD/VSS pairs, including VDDA/VSSA. The VCAP capacitors must be
150 milliohm or less ESR capacitors.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and
VSS pins are less than 0.5 inch per capacitor lead.
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and VSS.
Bypass the VDD and VSS layers of the PCB with approximately 100 F, preferably with a high-
grade capacitor such as a tantalum capacitor.
Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal.
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating
capacitance. This is especially critical in systems with higher capacitive loads that could create
higher transient currents in the VDD and VSScircuits.
Take special care to minimize noise levels on the VREF, VDDA and VSSA pins.
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or electrical
fields. However, normal precautions are advised to
avoid application of any voltages higher than maximum
rated voltages to this high-impedance circuit. Reliability
of operation is enhanced if unused inputs are tied to an
appropriate voltage level.
相关PDF资料 |
PDF描述 |
|---|---|
| SPAK56F807VF80 | 16-BIT, 80 MHz, OTHER DSP, PBGA160 |
| SPAK56F826BU80 | 16-BIT, 80 MHz, OTHER DSP, PQFP100 |
| SPAK56F8346FV60 | 16-BIT, 240 MHz, OTHER DSP, PQFP144 |
| SPAKMC332ACFV10 | 32-BIT, MICROCONTROLLER, PQFP144 |
| SPAKXC16Z1MFC16 | 16-BIT, 16.78 MHz, MICROCONTROLLER, PQFP132 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPAKDSP303AG100 | 功能描述:数字信号处理器和控制器 - DSP, DSC SPAKDSP303AG100 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| SPAKDSP303GC100 | 制造商:Motorola Inc 功能描述: |
| SPAKDSP303VF100 | 功能描述:IC DSP 24BIT 100MHZ 196-MAPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:DSP563xx 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| SPAKDSP303VL100 | 功能描述:IC DSP 24BIT 100MHZ 196-MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:DSP563xx 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| SPAKDSP311VF150 | 功能描述:IC DSP 24BIT 196-MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:DSP56K/Symphony 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。