参数资料
型号: SST55LC100M-45-C-BWE
元件分类: 存储控制器/管理单元
英文描述: IDE COMPATIBLE, FLASH MEMORY DRIVE CONTROLLER, PBGA84
封装: 9 X 9 MM, ROHS COMPLIANT, TFBGA-84
文件页数: 3/75页
文件大小: 1040K
代理商: SST55LC100M-45-C-BWE
Advance Information
CompactFlash Card Controller
SST55LC100M
2006 Silicon Storage Technology, Inc.
S71316-00-000
3/06
11
IORD#
(Memory Card mode)
19
F1
I
I3U
This signal is not used in this mode.
IORD#
(PC Card I/O mode)
This is an I/O Read strobe generated by the host. This signal
gates I/O data onto the bus from the CompactFlash card when
the card is configured to use the I/O interface.
IORD#
(True IDE mode)
In True IDE mode, this signal has the same function as in PC
card I/O mode.
IOWR#
(Memory Card mode)
57
H9
I
I3U
This signal is not used in this mode.
IOWR#
(PC Card I/O mode)
The I/O Write strobe pulse is used to clock I/O data on the card
data bus into the CompactFlash card controller registers when
the CompactFlash card is configured to use the I/O interface.
IOWR#
(True IDE mode)
In True IDE mode, this signal has the same function as in PC
Card I/O mode.
OE#
(Memory Card mode)
13
D1
I
I3U
This is an Output Enable strobe generated by the host inter-
face. It is used to read data from the CompactFlash card in
Memory mode and to read the CIS and configuration registers.
OE#
(PC Card I/O mode)
In PC Card I/O mode, this signal is used to read the CIS and
configuration registers.
ATASEL#
(True IDE mode)
To enable True IDE mode this input should be grounded by the
host.
Ready
(Memory Card mode)
21
G1
O
O1
In Memory mode this signal is set high when the Compact-
Flash card is ready to accept a new data transfer operation
and held low when the card is busy.
At power up and at Reset, the Ready signal is held low (busy)
until the CompactFlash card has completed its power up or
reset function. No access of any type should be made to the
CompactFlash card during this time.
IREQ#
(PC Card I/O mode)
I/O Operation - After the CompactFlash card has been config-
ured for I/O operation, this signal is used as Interrupt Request.
This line is strobed low to generate a pulse mode interrupt or
held low for a level mode interrupt.
INTRQ
(True IDE mode)
In True IDE mode signal is the active high Interrupt Request to
the host.
REG#
(Memory Card mode)
20
G2
I
I3U
This signal is used during Memory cycles to distinguish
between Common Memory and Register (Attribute) Memory
Attribute Memory Select accesses. High for Common Memory,
Low for Attribute Memory.
REG#
(PC Card I/O mode)
The signal must also be active (low) during I/O Cycles when
the I/O address is on the Bus.
Reserved
(True IDE mode)
In True IDE mode this input signal is not used and should be
connected to VDD by the host.
TABLE
3-1:Pin Assignments (Continued) (3 of 6)
Signal Name
100-lead 84-ball
Pin
Type
I/O
Type1
Name and Functions
相关PDF资料
PDF描述
SST55LD017D-40-C-TQWE FLASH MEMORY DRIVE CONTROLLER, PQFP100
SST55LD017D-40-I-TQW FLASH MEMORY DRIVE CONTROLLER, PQFP100
SST55LD019A-45-C-TQPE FLASH MEMORY DRIVE CONTROLLER, PQFP64
SST55LD019C-45-I-BWE FLASH MEMORY DRIVE CONTROLLER, PBGA84
SST55LD019B-45-C-TQW FLASH MEMORY DRIVE CONTROLLER, PQFP100
相关代理商/技术参数
参数描述
SST55LC100M-45-C-TQWE 功能描述:总线收发器 Compact Flash 45MHz 3.3V Commercial RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel
SST55LC100M-45-I-BWE 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:CompactFlash Card Controller
SST55LC100M-45-I-TQWE 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:CompactFlash Card Controller
SST55LC200-60-C-TQWE 功能描述:闪存 Compact 闪存 60MHz 3.3V Commercial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST55LC200-60-I-TQWE 功能描述:闪存 Compact 闪存 60MHz 3.3V Commercial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel