参数资料
型号: ST72324K6B3/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
封装: 0.400 INCH, SHRINK, PLASTIC, DIP-32
文件页数: 156/157页
文件大小: 1037K
代理商: ST72324K6B3/XXX
ST72324J/K
98/157
SERIAL COMMUNICATIONS INTERFACE (Cont’d)
CONTROL REGISTER 2 (SCICR2)
Read/Write
Reset Value: 0000 0000 (00h)
Bit 7 = TIE
Transmitter interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever
TDRE=1 in the SCISR register
Bit 6 = TCIE
Transmission complete interrupt ena-
ble
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever TC=1 in
the SCISR register
Bit 5 = RIE
Receiver interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever OR=1
or RDRF=1 in the SCISR register
Bit 4 = ILIE
Idle line interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SCI interrupt is generated whenever IDLE=1
in the SCISR register.
Bit 3 = TE
Transmitter enable.
This bit enables the transmitter. It is set and
cleared by software.
0: Transmitter is disabled
1: Transmitter is enabled
Note: During transmission, a “0” pulse on the TE
bit (“0” followed by “1”) sends a preamble after the
current word.
Caution: The TDO pin is free for general purpose
I/O only when the TE and RE bits are both cleared
(or if TE is never set).
Bit 2 = RE
Receiver enable.
This bit enables the receiver. It is set and cleared
by software.
0: Receiver is disabled
1: Receiver is enabled and begins searching for a
start bit
Bit 1 = RWU
Receiver wake-up.
This bit determines if the SCI is in mute mode or
not. It is set and cleared by software and can be
cleared by hardware when a wake-up sequence is
recognized.
0: Receiver in Active mode
1: Receiver in Mute mode
Note: Before selecting Mute mode (setting the
RWU bit), the SCI must receive some data first,
otherwise it cannot function in Mute mode with
wakeup by idle line detection.
Bit 0 = SBK
Send break.
This bit set is used to send break characters. It is
set and cleared by software.
0: No break character is transmitted
1: Break characters are transmitted
Note: If the SBK bit is set to “1” and then to “0”, the
transmitter will send a BREAK word at the end of
the current word.
70
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
相关PDF资料
PDF描述
ST72324J6B3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST72324J6T3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
ST72325J4B6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST72325J6B3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST72325K6B6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
相关代理商/技术参数
参数描述
ST72324K6T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, 4 TIMERS, SPI, SCI INTERFACE
ST72324Kx 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V RANGE 8-BIT MCU WITH 8 TO 32K FLASH,10-BIT ADC, 4 TIMERS,SPI,SCI INTERFACE
ST72324LJ2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3V range 8-bit MCU with 8 to 32K Flash/ROM, 10-bit ADC, 4 timers, SPI, SCI interface
ST72324LJ4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3V range 8-bit MCU with 8 to 32K Flash/ROM, 10-bit ADC, 4 timers, SPI, SCI interface
ST72324LJ6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3V range 8-bit MCU with 8 to 32K Flash/ROM, 10-bit ADC, 4 timers, SPI, SCI interface