参数资料
型号: ST7PLUSA2M3
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件页数: 50/136页
文件大小: 1705K
代理商: ST7PLUSA2M3
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
Flash program memory
ST7LITEUS2, ST7LITEUS5
Pin 9 has to be connected to the CLKIN pin of the ST7 when I2C mode is selected with
option bytes disabled (35-pulse I2C entry mode). When option bytes are enabled (38-pulse
I2C entry mode), the internal RC clock (internal RC or AWU RC) is forced. If internal RC is
selected in the option byte, the internal RC is provided. If AWU RC or external clock is
selected, the AWU RC oscillator is provided.
A serial resistor must be connected to I2C connector pin 6 in order to prevent contention on
PA3/RESET pin. Contention may occur if a tool forces a state on RESET pin while PA3 pin
forces the opposite state in output mode. The resistor value is defined to limit the current
below 2 mA at 5 V. If PA3 is used as output push-pull, then the application must be switched
off to allow the tool to take control of the RESET pin (PA3). To allow the programming tool to
drive the RESET pin below VIL, special care must also be taken when a pull-up is placed on
PA3 for application reasons.
Caution:
During normal operation, ICCCLK pin must be pulled- up, internally or externally (external
pull-up of 10 k
Ω mandatory in noisy environment). This is to avoid entering I2C mode
unexpectedly during a reset. In the application, even if the pin is configured as output, any
reset will put it back in input pull-up.
Figure 6.
Typical I2C interface
4.5
Memory protection
There are two different types of memory protection: readout protection and Write/Erase
Protection which can be applied individually.
4.5.1
Readout protection
Readout protection, when selected provides a protection against program memory content
extraction and against write access to Flash memory. Even if no protection can be
considered as totally unbreakable, the feature provides a very high level of protection for a
general purpose microcontroller. Program memory is protected.
I2C CONNECTOR
ICC
D
A
T
A
IC
CCLK
RESET
V
DD
HE10 CONNECTOR TYPE
APPLICATION
POWER SUPPLY
1
2
4
6
8
10
97
5
3
PROGRAMMING TOOL
I2C CONNECTOR
APPLICATION BOARD
I2C Cable
(See Note 3)
ST7
CL
KIN
OPTIONAL
See Note 1
See Note 1 and Caution
See Note 2
APPLICATION
RESET SOURCE
APPLICATION
I/O
(See Note 4)
3.3k
Ω
(See Note 5)
相关PDF资料
PDF描述
ST7PMC1K2TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32
ST7FMC2S4TC 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST7FMC2S6TC 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST7PMC2S4TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
ST7PMC2S5TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI