参数资料
型号: ST7PLUSA2M3
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件页数: 59/136页
文件大小: 1705K
代理商: ST7PLUSA2M3
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
ST7LITEUS2, ST7LITEUS5
Supply, reset and clock management
Note:
1
In I2C mode, the internal RC oscillator is forced as a clock source, regardless of the
selection in the option byte. Refer to note 5 in Section 4.4 on page 19 for further details.
2See Section 12: Electrical characteristics for more information on the frequency and
accuracy of the RC oscillator.
3
To improve clock stability and frequency accuracy, it is recommended to place a decoupling
capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7
device.
Caution:
If the voltage or temperature conditions change in the application, the frequency may need
to be recalibrated.
Refer to application note AN2326 for information on how to calibrate the RC frequency using
an external reference signal.
The ST7LITEUS2 and ST7LITEUS5 also contain an Auto-wakeup RC oscillator. This RC
oscillator should be enabled to enter Auto-wakeup from Halt mode.
The Auto-wakeup RC oscillator can also be configured as the startup clock through the
CKSEL[1:0] option bits (see Section 14.1 on page 123).
This is recommended for applications where very low power consumption is required.
Switching from one startup clock to another can be done in run mode as follows (see
Case 1
Switching from internal RC to AWU:
1.
Set the RC/AWU bit in the CKCNTCSR register to enable the AWU RC oscillator
2.
The RC_FLAG is cleared and the clock output is at 1.
3.
Wait 3 AWU RC cycles till the AWU_FLAG is set
4.
The switch to the AWU clock is made at the positive edge of the AWU clock signal
5.
Once the switch is made, the internal RC is stopped
Case 2
Switching from AWU RC to internal RC:
1.
Reset the RC/AWU bit to enable the internal RC oscillator
2.
Using a 4-bit counter, wait until 8 internal RC cycles have elapsed. The counter is
running on internal RC clock.
3.
Wait till the AWU_FLAG is cleared (1AWU RC cycle) and the RC_FLAG is set (2 RC
cycles)
4.
The switch to the internal RC clock is made at the positive edge of the internal RC clock
signal
5.
Once the switch is made, the AWU RC is stopped
Note:
1
When the internal RC is not selected, it is stopped so as to save power consumption.
2
When the internal RC is selected, the AWU RC is turned on by hardware when entering
Auto-wakeup from Halt mode.
3
When the external clock is selected, the AWU RC oscillator is always on.
相关PDF资料
PDF描述
ST7PMC1K2TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32
ST7FMC2S4TC 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST7FMC2S6TC 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
ST7PMC2S4TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
ST7PMC2S5TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI