- 您现在的位置：买卖IC网 > PDF目录98254 > TLV320AIC32IRHB (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF资料下载
参数资料
| 型号： | TLV320AIC32IRHB |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封装： | 5 X 5 MM, PLASTIC, QFN-32 |
| 文件页数： | 27/76页 |
| 文件大小： | 1124K |
| 代理商： | TLV320AIC32IRHB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
www.ti.com
ANALOG HIGH POWER OUTPUT DRIVERS
SLAS479B – AUGUST 2005 – REVISED AUGUST 2006
on the requirements of the system. If mixing of the DAC audio with other signals is not required, and the DAC
output is only needed at the stereo line outputs, then it is recommended to use the routing through path
DAC_L3/R3 to the fully differential stereo line outputs. This results not only in higher quality output performance,
but also in lower power operation, since the analog volume controls and mixing blocks ahead of these drivers
can be powered down. This signal path will attenuate the signal by a factor of 1 dB.
If instead the DAC analog output must be routed to multiple output drivers simultaneously (such as to
LEFT_LOP/M, and RIGHT_LOP/M) or must be mixed with other analog signals, then the DAC outputs should be
switched through the DAC_L1/R1 path. This option provides the maximum flexibility for routing of the DAC
analog signals to the output drivers
The TLV320AIC32 includes an output level control on each output driver with limited gain adjustment from 0 dB
to 9 dB. The output driver circuitry in this device are designed to provide a low distortion output while playing
fullscale stereo DAC signals at a 0dB gain setting. However, a higher amplitude output can be obtained at the
cost of increased signal distortion at the output. This output level control allows the user to make this tradeoff
based on the requirements of the end equipment. Note that this output level control is not intended to be used
as a standard output volume control. It is expected to be used only sparingly for level setting, i.e., adjustment of
the fullscale output range of the device.
Each differential line output driver can be powered down independently of the others when it is not needed in the
system. When placed into powerdown through register programming, the driver output pins will be placed into a
tri-stated, high-impedance state.
The TLV320AIC32 includes four high power output drivers with extensive flexibility in their usage. These output
drivers are individually capable of driving 30 mW each into a 16-
load in single-ended configuration, and they
can be used in pairs to drive up to 500 mW into an 8-
load connected in bridge-terminated load (BTL)
configuration between two driver outputs.
The high power output drivers can be configured in a variety of ways, including:
1. driving up to two fully differential output signals
2. driving up to four single-ended output signals
3. driving two single-ended output signals, with one or two of the remaining drivers driving a fixed VCM level,
for a pseudo-differential stereo output
4. driving one or two 8-
speakers connected BTL between pairs of driver output pins
5. driving stereo headphones in single-ended configuration with two drivers, while the remaining two drivers are
connected in BTL configuration to an 8-
speaker.
The output stage architecture leading to the high power output drivers is shown in Figure 31, with the volume
control and mixing blocks being effectively identical to that shown in Figure 30. Note that each of these drivers
have a output level control block like those included with the line output drivers, allowing gain adjustment up to
+9dB on the output signal. As in the previous case, this output level adjustment is not intended to be used as a
standard volume control, but instead is included for additional fullscale output signal level control.
Two of the output drivers, HPROUT and HPLOUT, include a direct connection path for the stereo DAC outputs
to be passed directly to the output drivers and bypass the analog volume controls and mixing networks, using
the DAC_L2/R2 path. As in the line output case, this functionality provides the highest quality DAC playback
performance with reduced power dissipation, but can only be utilized if the DAC output does not need to route to
multiple output drivers simultaneously, and if mixing of the DAC output with other analog signals is not needed.
The direct connection path will attenuate the signal by a factor of 1 dB.
33
相关PDF资料 |
PDF描述 |
|---|---|
| TLV320AIC33IGQER | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC33IGQE | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC33IRGZR | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TLV320AIC33IZQER | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC33IZQE | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV320AIC32IRHBG4 | 制造商:Texas Instruments 功能描述:AUD CODEC 2ADC / 2DAC 32BIT 32QFN EP - Rail/Tube |
| TLV320AIC32IRHBR | 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 6 Otp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC32IRHBRG4 | 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 6 Otp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC32IRHBT | 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 6 Otp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC32IRHBTG4 | 功能描述:接口—CODEC Lo-Pwr Stereo Codec w/6 Inp 6 Otp RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。