- 您现在的位置：买卖IC网 > PDF目录17451 > TPS51020EVM-001 (Texas Instruments)EVAL MODULE FOR TPS51020-001 PDF资料下载
参数资料
| 型号： | TPS51020EVM-001 |
| 厂商： | Texas Instruments |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | EVAL MODULE FOR TPS51020-001 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 3.3V，5V |
| 电流 - 输出： | 6A，6A |
| 输入电压： | 8 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | TPS51020 |
| 产品目录页面： | 1028 (CN2011-ZH PDF) |
| 相关产品： | TPS51020DBTRG4-ND - IC DUAL DC/DC SYNC CTRLR 30TSSOP 296-26971-2-ND - IC DUAL DC/DC SYNC CTRLR 30TSSOP TPS51020DBTG4-ND - IC DUAL DC/DC SYNC CTRLR 30TSSOP 296-15896-5-ND - IC DUAL DC/DC CTRLR SYNC 30TSSOP |
| 其它名称： | 296-18958 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TPS51020
SLUS564C ? JULY 2003 ? REVISED OCTOBER 2008
APPLICATION INFORMATION
PWM OPERATION
The PWM control block utilizes a fixed-frequency, feed-forward, voltage-mode control scheme with a
wide-bandwidth, low-impedance output error amplifier as the voltage servo control block. This scheme allows
the highest efficiency down conversion while maintaining excellent line regulation and fast transient response.
Loop compensation is programmed by connecting a filter network between the COMPx pin and the INVx pin.
The wide bandwidth error amplifier handles conventional Type II compensation or Type III compensation when
using ceramic capacitors for the converter output. For channel one, the reference signal for the control loop is
always a precision 0.85-V internal reference, while the channel two loop reference is either the 0.85-V reference
or, in the case of DDR mode, one half the VO1_VDDQ voltage, (VO1_VDDQ)/2. The output signal of the error
amplifier appears at the COMPx pin and is compared to a buffered version of the 0.6-V oscillator ramp. When
TRIP2 pin is tied to VIN through a resistor, the voltage ramp is further modulated by the input voltage, VIN, to
maintain a constant modulator gain. If the TRIP2 pin is connected to ground through a resistor, then the voltage
ramp remains fixed regardless of VIN value.
The oscillator frequency is internally fixed and can be selected at 270 kHz, 360 kHz or 470 kHz by insertion of
a clamping resistor on the SSTRTx pin per Table 1. For example, 470 kHz can be attained when both SSTRTx
voltages exceed 3.5 V, as described in WAVEFORM1. The controller begins with 270 kHz in the first stage of
the softstart, and then increases to 470 kHz at the steady state. When 270 kHz is selected, both of SSTRTx
voltages are kept below 3.5 V so that the frequency is the same 270 kHz for the entire operation.
Two channels are operated in 180 degrees out-of-phase interleave switching mode. This interleaving helps
reduce the input current ripple requirement for the input capacitor. However, because the PWM loop determines
both the turn-off AND turn-on of the high-side MOSFET, this 180 degree operation may not be apparent by
looking at the LLx nodes only. Rather, the turn-off cycle of one channel always corresponds to the turn-on cycle
of the other channel and vise-versa. As a result, input ripple is reduced and dynamic response is improved over
a broad input voltage range.
MAXIMUM DUTY CYCLE
Because most notebook applications typically run from three to four cell Li?Ion or run from a 20-V adapter, 100%
duty cycle operation is not required. Rather, the TPS51020 is optimized for low duty ratio step-down conversion.
As a result of limiting the duty cycle, the flying BST capacitor is refreshed reliably and the low-side over current
detection circuitry is capable of detecting an overcurrent condition even if the output is stuck between the
regulation point and UVP. The maximum duty cycle for each operating frequency is 88% for 270 kHz, 85% for
360 kHz and 82% for 470 kHz.
It should be noted that if the system is operating close to maximum (or minimum) duty cycle, it may be difficult
for the converter to respond quickly during line/load transients or state changes (such as frequency switching
during soft start or PWM to SKIP mode transitions). This slow response is due to the dynamic range of the COMP
pin and is usually not a result of poor phase compensation. In the case of minimum duty cycle operation, the
slow response is due to the minimum pulse width of the converter (100 ns TYP). In this case (counter intuitively),
it may be advisable to slow down the switching frequency of the converter in order to improve response time.
10
www.ti.com
相关PDF资料 |
PDF描述 |
|---|---|
| 306XC104B | TRIMMER 100K OHM 0.5W TH |
| ECC07DRES-S13 | CONN EDGECARD 14POS .100 EXTEND |
| 306XC503B | TRIMMER 50K OHM 0.5W TH |
| HBC05DRYN | CONN EDGECARD 10POS DIP .100 SLD |
| 306XC203B | TRIMMER 20K OHM 0.5W TH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS5102DBT | 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL, HIGH-EFFICIENCY CONTROLLER FOR NOTEBOOK PC POWER |
| TPS5102IDBR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| TPS5102IDBT | 功能描述:DC/DC 开关控制器 Dual Output Synch Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5102IDBTG4 | 功能描述:DC/DC 开关控制器 Dual Output Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5102IDBTR | 功能描述:DC/DC 开关控制器 Dual Output Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。