- 您现在的位置：买卖IC网 > PDF目录361590 > uPSD3212 (意法半导体) Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可编程系统器件) PDF资料下载
参数资料
| 型号： | uPSD3212 |
| 厂商： | 意法半导体 |
| 英文描述： | Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可编程系统器件) |
| 中文描述： | 闪存可编程系统器件与8032微控制器内核（嵌入高速“8032微控制器核”的闪存型可编程系统器件） |
| 文件页数： | 91/155页 |
| 文件大小： | 1055K |
| 代理商： | UPSD3212 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页当前第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页
91/155
μPSD321X
Programming Flash Memory
Flash memory must be erased prior to being pro-
grammed. A byte of Flash memory is erased to all
’1s’ (FFh), and is programmed by setting selected
bits to ’0.’ The MCU may erase Flash memory all
at once or by-sector, but not byte-by-byte. Howev-
er, the MCU may program Flash memory byte-by-
byte.
The primary and secondary Flash memories re-
quire the MCU to send an instruction to program a
byte or to erase sectors (see Table 62).
Once the MCU issues a Flash memory Program or
Erase instruction, it must check for the status bits
for completion. The embedded algorithms that are
invoked support several means to provide status
to the MCU. Status may be checked using any of
three methods: Data Polling, Data Toggle, or
Ready/Busy (PC3).
Data Polling.
Polling on the Data Polling Flag Bit
(DQ7) is a method of checking whether a Program
or Erase cycle is in progress or has completed.
Figure 42 shows the Data Polling algorithm.
When the MCU issues a Program instruction, the
embedded algorithm begins. The MCU then reads
the location of the byte to be programmed in Flash
memory to check status. The Data Polling Flag Bit
(DQ7) of this location becomes the complement of
b7 of the original data byte to be programmed. The
MCU continues to poll this location, comparing the
Data Polling Flag Bit (DQ7) and monitoring the Er-
ror Flag Bit (DQ5). When the Data Polling Flag Bit
(DQ7) matches b7 of the original data, and the Er-
ror Flag Bit (DQ5) remains ’0,’ the embedded algo-
rithm is complete. If the Error Flag Bit (DQ5) is ’1,’
the MCU should test the Data Polling Flag Bit
(DQ7) again since the Data Polling Flag Bit (DQ7)
may have changed simultaneously with the Error
Flag Bit (DQ5) (see Figure 42).
The Error Flag Bit (DQ5) is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte or if the MCU at-
tempted to program a ’1’ to a bit that was not
erased (not erased is logic ’0’).
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
ming algorithm has completed, to compare the
byte that was written to the Flash memory with the
byte that was intended to be written.
When using the Data Polling method during an
Erase cycle, Figure 42 still applies. However, the
Data Polling Flag Bit (DQ7) is ’0’ until the Erase cy-
cle is complete. A ’1’ on the Error Flag Bit (DQ5) in-
dicates a time-out condition on the Erase cycle; a
’0’ indicates no error. The MCU can read any loca-
tion within the sector being erased to get the Data
Polling Flag Bit (DQ7) and the Error Flag Bit
(DQ5).
PSDsoft Express generates ANSI C code func-
tions which implement these Data Polling algo-
rithms.
Figure 42. Data Polling Flowchart
READ DQ5 & DQ7
at VALID ADDRESS
START
READ DQ7
FAIL
PASS
AI01369B
D=
DATA
YES
NO
YES
NO
DQ5
= 1
D=
DATA
YES
NO
相关PDF资料 |
PDF描述 |
|---|---|
| UPSD3215A-24T1 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| UPSD3215AV-40T6T | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| UPSD3215BV-24U1 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| UPSD3233A-40T6 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| UPSD3233AV-40T1 | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
相关代理商/技术参数 |
参数描述 |
|---|---|
| UPSD3212A | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212A-24T6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212A-24U6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
| UPSD3212A-40T6 | 功能描述:8位微控制器 -MCU Flash Programmable System Devices RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| UPSD3212A-40T6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic |
发布紧急采购，3分钟左右您将得到回复。