- 您现在的位置：买卖IC网 > PDF目录68428 > W25Q80BVZPAG (WINBOND ELECTRONICS CORP) 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25Q80BVZPAG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 6 X 5 MM, GREEN, WSON-8 |
| 文件页数： | 40/75页 |
| 文件大小： | 1055K |
| 代理商： | W25Q80BVZPAG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
W25Q80BV
Publication Release Date: October 06, 2010
- 45 -
Revision D
9.2.27 Erase / Program Suspend (75h)
The Erase/Program Suspend instruction “75h”, allows the system to interrupt a Sector or Block Erase
operation or a Page Program operation and then read from or program/erase data to, any other sectors
or blocks. The Erase/Program Suspend instruction sequence is shown in figure 25.
The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h, 44h) are not
allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If
written during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status
Register instruction (01h) and Program instructions (02h, 32h, 42h) are not allowed during Program
Suspend. Program Suspend is valid only during the Page Program or Quad Page Program operation.
The Erase/Program Suspend instruction “75h” will be accepted by the device only if the SUS bit in the
Status Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase or a Page
Program operation is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend
instruction will be ignored by the device. A maximum of time of “tSUS” (See AC Characteristics) is required
to suspend the erase or program operation. The BUSY bit in the Status Register will be cleared from 1 to
0 within “tSUS” and the SUS bit in the Status Register will be set from 0 to 1 immediately after
Erase/Program Suspend. For a previously resumed Erase/Program operation, it is also required that the
Suspend instruction “75h” is not issued earlier than a minimum of time of “tSUS” following the preceding
Resume instruction “7Ah”.
Unexpected power off during the Erase/Program suspend state will reset the device and release the
suspend state. SUS bit in the Status Register will also reset to 0. The data within the page, sector or
block that was being suspended may become corrupted. When the device is powered up again, it is
recommended for the user to repeat the same Erase or Program operation that was interrupted, at the
same address location, to avoid the potention data corruption.
/CS
CLK
DI
(IO
0)
DO
(IO
1)
Mode 0
Mode 3
0
1
2
3
4
5
6
7
Instruction (75h)
High Impedance
Mode 0
Mode 3
tSUS
Accept instructions
Figure 25. Erase/Program Suspend Instruction Sequence
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q80BVSNIP | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25X10AVDIAZ | 128K X 8 FLASH 2.7V PROM, PDIP8 |
| W25X16AVDAIG | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X16BVZPIG | 256K X 16 FLASH 2.7V PROM, PDSO8 |
| W25X20BLSNIG | 2M X 1 FLASH 2.7V PROM, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q80BVZPAP | 制造商:WINBOND 制造商全称:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BVZPIG | 功能描述:IC SPI FLASH 8MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR) |
| W25Q80BVZPIG TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 8MBIT 104MHZ 8WSON |
| W25Q80BVZPIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q80BW | 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
发布紧急采购，3分钟左右您将得到回复。