参数资料
型号: W25X10BVZPIG
厂商: Winbond Electronics
文件页数: 10/51页
文件大小: 0K
描述: IC SPI FLASH 1MBIT 8WSON
标准包装: 100
系列: SpiFlash®
格式 - 存储器: 闪存
存储器类型: FLASH
存储容量: 1M (128K x 8)
速度: 104MHz
接口: SPI 串行
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-WDFN 裸露焊盘
供应商设备封装: 8-WSON(6x5)
包装: 管件
W25X10BV/20BV/40BV
8.2
WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and
other adverse system conditions that may compromise data integrity. To address this concern the
W25X10BV/20BV/40BV provides several means to protect data from inadvertent writes.
8.2.1
Write Protect Features
?
?
?
?
?
?
?
Device resets when VCC is below threshold.
Time delay write disable after Power-up.
Write enable/disable instructions.
Automatic write disable after program and erase.
Software write protection using Status Register.
Hardware write protection using Status Register and /WP pin.
Write Protection using Power-down instruction.
Upon power-up or at power-down the W25X10BV/20BV/40BV will maintain a reset condition while
VCC is below the threshold value of V WI , (See Power-up Timing and Voltage Levels and Figure 25).
While reset, all operations are disabled and no instructions are recognized. During power-up and after
the VCC voltage exceeds V WI , all program and erase related instructions are further disabled for a
time delay of t PUW . This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip
Erase and the Write Status Register instructions. Note that the chip select pin (/CS) must track the
VCC supply level at power-up until the VCC-min level and t VSL time delay is reached. If needed a pull-
up resister on /CS can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register
Write Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page
Program, Sector Erase, Chip Erase or Write Status Register instruction will be accepted. After
completing a program, erase or write instruction the Write Enable Latch (WEL) is automatically
cleared to a write-disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP) and Block Protect (TB, BP2, BP1, and BP0) bits. These Status
Register bits allow a portion or all of the memory to be configured as read only. Used in conjunction
with the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under
hardware control. See Status Register for further information.
Additionally, the Power-down instruction offers an extra level of write protection as all instructions are
ignored except for the Release Power-down instruction.
- 10 -
相关PDF资料
PDF描述
ISL9011IRKPZ IC REG LDO 2.85V/1.85V 10-DFN
VE-J3X-CX-S CONVERTER MOD DC/DC 5.2V 75W
R0.5Z-0512/H CONV DC/DC 0.5W 05VIN 12VOUT
EBM28DRXH CONN EDGE DUAL .156 DIP 56POS
TAJC476K020RNJ CAP TANT 47UF 20V 10% 2312
相关代理商/技术参数
参数描述
W25X10CLSNIG 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 2.5V/3.3V 1Mbit 128K/64K x 8bit/16bit 8ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8SOIC
W25X10CLSNIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 1M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W25X10CLZPIG 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON
W25X10CLZPIG TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON
W25X10L 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT, 4M-BIT AND 8M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI