参数资料
| 型号： | W29GL128CH9B |
| 厂商： | Winbond Electronics |
| 文件页数： | 19/67页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 128MBIT 90NS 64LFBGA |
| 标准包装： | 171 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 128M（16M x 8，8M x 16） |
| 速度： | 90ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-LBGA |
| 供应商设备封装： | 64-LFBGA（11x13） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
W29GL128C
7.2.17.3
Read Silicon Device ID Code
To verify the Silicon Device ID Codes, execute a Read Operation with V HH applied to the A9 pin and
address pins A6, A3, A2, A1, and A0 have several bit combinations to return the Winbond Device ID
codes of 7Eh, 21h or 01h, which is shown on the data bits DQ[7:0]. See Table 7-2 .
7.2.17.4
Read Indicator Bit DQ7 for Security Sector High and Low Address
To verify that the Security Sector has been factory locked, execute a Read Operation with V HH applied
to A9, address pins A6, A3, and A2 are held Low, and address pins A1 and A0 are held High. If the
Security Sector has been factory locked, the code 99h(Highest Address Sector) or 89h(Lowest
Address Sector) will be shown on the data bits DQ[7:0]. Otherwise, the factory unlocked code of
19h(H)/09(L) will be shown.
7.2.18 Automatic Select Operations
The Automatic Select instruction show in Table 7-13 can be executed if the device is in one of the
following modes; Read, Program Suspended, Erase-Suspended Read, or CFI. At which time the user
can issue (two unlock cycles followed by the Automatic Select instruction 90h) to enter Automatic
Select mode. Once in the Automatic Select mode, the user can query the Manufacturer ID, Device ID,
Security Sector locked status, or Sector protected status multiple times without executing the unlock
cycles and a Automatic Select instruction (90h) again.
Once in Automatic Select mode, executing a Reset instruction (F0h) will return the device back to the
valid mode from which it left when the Automatic Select mode was first executed.
Another way previously mentioned to enter Automatic Select mode is to use one of the bus operation
shown Table 7-2 in Device Bus Operation. Once the high voltage (V HH ) is removed from the A9 pin,
the device will return back to the valid mode from which it left when the Automatic Select mode was
first executed.
7.2.19
Automatic Select Instruction Sequence
Accessing the manufacturer ID, device ID, and verifying whether or not secured silicon is locked and
whether or not a sector protected is the purpose of Automatic Select mode. There are four instruction
cycles that comprise the Automatic Select mode. The first two cycles are write unlock commands,
followed by the Automatic Select instruction (90h). The fourth cycle is a read cycle, and the user may
read at any address any number of times without entering another instruction sequence. To exit the
Automatic Select mode and back to read array, the Reset instruction is necessary. No other
instructions are allowed except the Reset Instruction once Automatic Select mode has been selected.
Refer to the following table for more detailed information.
Address
Data (hex)
Representation
Manufacturer ID
Device ID W29GL128C
Word
Byte
Word
Byte
X00
X00
X01/0E/0F
X02/1C/1E
01
01
227E/2221/2201
7E/21/01
Secure Silicon
Word
Byte
X03
X06
99/19(H)
89//09(L)
99/19(H)
89/09(L)
Factory locked/unlocked
Factory locked/unlocked
Sector Protect Verify
Word (Sector address) X02
Byte Sector address) X04
00/01
00/01
Unprotected/protected
Unprotected/protected
Table 7-9
Auto Select for MFR/Device ID/Secure Silicon/Sector Protect Read
Publication Release Date: August 2, 2013
13
Revision H
相关PDF资料 |
PDF描述 |
|---|---|
| W949D6CBHX5E | IC LPDDR SDRAM 512MBIT 60VFBGA |
| APA150-FGG144A | IC FPGA PROASIC+ 150K 144-FBGA |
| APA150-FG144A | IC FPGA PROASIC+ 150K 144-FBGA |
| A54SX16A-FG256 | IC FPGA SX 24K GATES 256-FBGA |
| A54SX16A-FGG256 | IC FPGA SX 24K GATES 256-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL128CH9B TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 64LFBGA |
| W29GL128CH9T | 功能描述:IC FLASH 128MBIT 90NS 56TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| W29GL128CH9T TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 56TSOP |
| W29GL128CL9B | 功能描述:IC FLASH 128MBIT 90NS 64LFBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G（256M x 16） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6 |
| W29GL128CL9B TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 64LFBGA |
发布紧急采购，3分钟左右您将得到回复。