- 您现在的位置：买卖IC网 > PDF目录18683 > XBIB-R (Digi International/Maxstream)BOARD RS232 ZIGBEE MOD PRO PDF资料下载
参数资料
| 型号： | XBIB-R |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 22/72页 |
| 文件大小： | 1116K |
| 描述： | BOARD RS232 ZIGBEE MOD PRO |
| 设计资源： | XBIB-R Schematic |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | XBee 和 XBee Pro 收音机 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?2
Chapter??燫F燤odule燨peration
2.5.3. Sleep Mode
Sleep Modes enable the RF module to enter states of low-power consumption when not in use. In
order to enter Sleep Mode, one of the following conditions must be met (in addition to the module
having a non-zero SM parameter value):
" Sleep_RQ (pin 9) is asserted.
" The module is idle (no data transmission or reception) for the amount of time defined by the
ST (Time before Sleep) parameter. [NOTE: ST is only active when SM = 4-5.]
The SM command is central to setting Sleep Mode configurations. By default, Sleep Modes are dis-
abled (SM = 0) and the module remains in Idle/Receive Mode. When in this state, the module is
constantly ready to respond to serial or RF activity.
Higher Voltages. Sleep Mode current consumption is highly sensitive to voltage. Voltages above
3.0V will cause much higher current consumption.
Pin/Host-controlled Sleep Modes
The transient current when waking from pin sleep (SM = 1 or 2) does not exceed the idle current
of the module. The current ramps up exponentially to its idle current.
Pin Hibernate (SM = 1)
" Pin/Host-controlled
" Typical power-down current: < 10 礎 (@3.0 VCC)
" Wake-up time: 13.2 msec
Pin Hibernate Mode minimizes quiescent power (power consumed when in a state of rest or inac-
tivity). This mode is voltage level-activated; when Sleep_RQ is asserted, the module will finish any
transmit, receive or association activities, enter Idle Mode and then enter a state of sleep. The
module will not respond to either serial or RF activity while in pin sleep.
To wake a sleeping module operating in Pin Hibernate Mode, de-assert Sleep_RQ (pin 9). The
module will wake when Sleep_RQ is de-asserted and is ready to transmit or receive when the CTS
line is low. When waking the module, the pin must be de-asserted at least two 'byte times' after
CTS
goes low. This assures that there is time for the data to enter the DI buffer.
Table?04. Sleep燤ode燙onfigurations
Sleep Mode
Setting
Transition into
Sleep Mode
Transition out of
Sleep Mode (wake)
Characteristics
Related
Commands
Power
Consumption
Pin Hibernate
(SM = 1)
Assert (high) Sleep_RQ
(pin 9)
De-assert (low) Sleep_RQ
Pin/Host-controlled /
NonBeacon systems
only / Lowest Power
(SM)
< 10 礎 (@3.0
VCC)
Pin Doze
(SM = 2)
Assert (high) Sleep_RQ
(pin 9)
De-assert (low) Sleep_RQ
Pin/Host-controlled /
NonBeacon systems
only / Fastest wake-up
(SM)
< 50 礎
Cyclic Sleep
(SM = 4 - 5)
Automatic transition to
Sleep Mode as defined by
the SM (Sleep Mode) and
ST (Time before Sleep)
parameters.
Transition occurs after the
cyclic sleep time interval
elapses. The time interval
is defined by the SP
(Cyclic Sleep Period)
parameter.
RF module wakes in
pre-determined time
intervals to detect if RF
data is present / When
SM = 5, NonBeacon
systems only
(SM), SP, ST
< 50 礎
when sleeping
Table?05. Sample燬leep燤ode燙urrents
XBee
XBee-PRO
Vcc (V)
SM=1
SM=2
SM=4,5
SM=1
SM=2
SM=4,5
2.83.0
<3 礎
<35uA
<34uA
<4uA
<34uA
<34uA
3.1
8uA
37mA
36uA
12uA
39uA
37uA
3.2
32uA
48uA
49uA
45uA
60uA
55uA
3.3
101uA
83uA
100uA
130uA
115uA
120uA
3.4
255uA
170uA
240uA
310uA
260uA
290uA
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-01-0000-00FD4 | XLAMP XPG LED COMM WARM/NTRL WHT |
| OPB480T11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
| XPERDO-L1-0000-00A03 | XLAMP XP-E LED - RED-ORANGE |
| XPEHEW-L1-0000-00H50 | LED XLAMP XPE HIEFF WHITE SMD |
| OPB480P11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XBIB-R-DEV | 功能描述:界面开发工具 RS-232 XBee-PRO pro onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U | 功能描述:界面开发工具 USB XBee-PRO interf -PRO interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-DEV | 功能描述:界面开发工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SP | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SS | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。