- 您现在的位置：买卖IC网 > PDF目录18683 > XBIB-R (Digi International/Maxstream)BOARD RS232 ZIGBEE MOD PRO PDF资料下载
参数资料
| 型号： | XBIB-R |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 26/72页 |
| 文件大小： | 1116K |
| 描述： | BOARD RS232 ZIGBEE MOD PRO |
| 设计资源： | XBIB-R Schematic |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | XBee 和 XBee Pro 收音机 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?6
Chapter??燫F燤odule燙onfiguration
3.2. Command Reference Tables
XBee/XBee-PRO RF Modules expect numerical values in hexadecimal. Hexadecimal values are des-
ignated by a 0x prefix. Decimal equivalents are designated by a d suffix. Commands are con-
tained within the following command categories (listed in the order that their tables appear):
" Special
" Networking & Security
" RF Interfacing
" Sleep (Low Power)
" Serial Interfacing
" I/O Settings
" Diagnostics
" AT Command Options
All modules within a PAN should operate using the same firmware version.
Special
*燜irmware爒ersion爄n爓hich爐he燾ommand爓as爁irst爄ntroduced?firmware爒ersions燼re爊umbered爄n爃exadecimal爊otation.)
Networking & Security
Table?01. XBeePRO燙ommands?燬pecial
AT
Command
Command
Category
Name and Description
Parameter Range
Default
WR
Special
Write. Write parameter values to non-volatile memory so that parameter modifications
persist through subsequent power-up or reset.
Note: Once WR is issued, no additional characters should be sent to the module until
after the response "OK\r" is received.
-
-
RE
Special
Restore Defaults. Restore module parameters to factory defaults.
-
-
FR ( v1.x80*)
Special
Software Reset. Responds immediately with an OK then performs a hard reset
~100ms later.
-
-
Table?02. XBee/XBeePRO燙ommands?燦etworking?燬ecurity?/SPAN>(Subcategories?/SPAN>designated?/SPAN>within?/SPAN>{brackets})
AT
Command
Command
Category
Name and Description
Parameter Range
Default
CH
Networking
{Addressing}
Channel. Set/Read the channel number used for transmitting and receiving data
between RF modules (uses 802.15.4 protocol channel numbers).
0x0B - 0x1A (XBee)
0x0C - 0x17 (XBee-PRO)
0x0C (12d)
ID
Networking
{Addressing}
PAN ID. Set/Read the PAN (Personal Area Network) ID.
Use 0xFFFF to broadcast messages to all PANs.
0 - 0xFFFF
0x3332
(13106d)
DH
Networking
{Addressing}
Destination Address High. Set/Read the upper 32 bits of the 64-bit destination
address. When combined with DL, it defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
0 - 0xFFFFFFFF
0
DL
Networking
{Addressing}
Destination Address Low. Set/Read the lower 32 bits of the 64-bit destination
address. When combined with DH, DL defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
0 - 0xFFFFFFFF
0
MY
Networking
{Addressing}
16-bit Source Address. Set/Read the RF module 16-bit source address. Set MY =
0xFFFF to disable reception of packets with 16-bit addresses. 64-bit source address
(serial number) and broadcast address (0x000000000000FFFF) is always enabled.
0 - 0xFFFF
0
SH
Networking
{Addressing}
Serial Number High. Read high 32 bits of the RF module's unique IEEE 64-bit
address. 64-bit source address is always enabled.
0 - 0xFFFFFFFF [read-only]
Factory-set
SL
Networking
{Addressing}
Serial Number Low. Read low 32 bits of the RF module's unique IEEE 64-bit address.
64-bit source address is always enabled.
0 - 0xFFFFFFFF [read-only]
Factory-set
RR ( v1.xA0*)
Networking
{Addressing}
XBee Retries. Set/Read the maximum number of retries the module will execute in
addition to the 3 retries provided by the 802.15.4 MAC. For each XBee retry, the
802.15.4 MAC can execute up to 3 retries.
0 - 6
0
RN
Networking
{Addressing}
Random Delay Slots. Set/Read the minimum value of the back-off exponent in the
CSMA-CA algorithm that is used for collision avoidance. If RN = 0, collision avoidance
is disabled during the first iteration of the algorithm (802.15.4 - macMinBE).
0 - 3 [exponent]
0
MM ( v1.x80*)
Networking
{Addressing}
MAC Mode. Set/Read MAC Mode value. MAC Mode enables/disables the use of a
MaxStream header in the 802.15.4 RF packet. When Mode 0 is enabled (MM=0),
duplicate packet detection is enabled as well as certain AT commands. Modes 1 and 2
are strict 802.15.4 modes.
0 - 2
0 = MaxStream Mode
1 = 802.15.4 (no ACKs)
2 = 802.15.4 (with ACKs)
0
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-01-0000-00FD4 | XLAMP XPG LED COMM WARM/NTRL WHT |
| OPB480T11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
| XPERDO-L1-0000-00A03 | XLAMP XP-E LED - RED-ORANGE |
| XPEHEW-L1-0000-00H50 | LED XLAMP XPE HIEFF WHITE SMD |
| OPB480P11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XBIB-R-DEV | 功能描述:界面开发工具 RS-232 XBee-PRO pro onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U | 功能描述:界面开发工具 USB XBee-PRO interf -PRO interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-DEV | 功能描述:界面开发工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SP | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SS | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。