- 您现在的位置：买卖IC网 > PDF目录18683 > XBIB-R (Digi International/Maxstream)BOARD RS232 ZIGBEE MOD PRO PDF资料下载
参数资料
| 型号： | XBIB-R |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 49/72页 |
| 文件大小： | 1116K |
| 描述： | BOARD RS232 ZIGBEE MOD PRO |
| 设计资源： | XBIB-R Schematic |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | XBee 和 XBee Pro 收音机 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?9
Chapter??燫F燤odule燙onfiguration
PR (Pull-up Resistor Enable) Command
<Serial Interfacing> The PR command is used to
set and read the bit field that is used to configure
internal the pull-up resistor status for I/O lines.
1 specifies the pull-up resistor is enabled. 0
specifies no pull up.
bit 0 - AD4/DIO4 (pin 11)
bit 1 - AD3/DIO3 (pin 17)
bit 2 - AD2/DIO2 (pin 18)
bit 3 - AD1/DIO1 (pin 19)
bit 4 - AD0/DIO0 (pin 20)
bit 5 - AD6/DIO6 (pin 16)
bit 6 - DI8 (pin 9)
bit 7 - DIN/CONFIG (pin 3)
For example: Sending the command ATPR 6F will turn bits 0, 1, 2, 3, 5 and 6 ON; and bits 4 & 7
will be turned OFF. (The binary equivalent of 0x6F is 01101111 . Note that bit 0 is the last digit
in the bitfield.
PT (PWM Output Timeout) Command
<I/O Settings {I/O Line Passing}> The PT com-
mand is used to set/read the output timeout
value for both PWM outputs.
When PWM is set to a non-zero value: Due to I/O
line passing, a time is started which when expired
will set the PWM output to zero. The timer is reset
when a valid I/O packet is received.
RE (Restore Defaults) Command
<(Special)> The RE command is used to restore
all configurable parameters to their factory
default settings. The RE command does not write
restored values to non-volatile (persistent) memory. Issue the WR (Write) command subsequent
to issuing the RE command to save restored parameter values to non-volatile memory.
RN (Random Delay Slots) Command
<Networking & Security> The RN command is
used to set and read the minimum value of the
back-off exponent in the CSMA-CA algorithm. The
CSMA-CA algorithm was engineered for collision
avoidance (random delays are inserted to prevent
data loss caused by data collisions).
If RN = 0, collision avoidance is disabled during the first iteration of the algorithm (802.15.4 -
macMinBE).
CSMA-CA stands for "Carrier Sense Multiple Access - Collision Avoidance". Unlike CSMA-CD (reacts
to network transmissions after collisions have been detected), CSMA-CA acts to prevent data colli-
sions before they occur. As soon as a module receives a packet that is to be transmitted, it checks
if the channel is clear (no other module is transmitting). If the channel is clear, the packet is sent
over-the-air. If the channel is not clear, the module waits for a randomly selected period of time,
then checks again to see if the channel is clear. After a time, the process ends and the data is lost.
AT Command: ATPR
Parameter Range: 0 - 0xFF
Default Parameter Value: 0xFF
(all pull-up resistors are enabled)
Minimum Firmware Version Required: v1.x80
AT Command: ATPT
Parameter Range: 0 - 0xFF [x 100 msec]
Default Parameter Value: 0xFF
Minimum Firmware Version Required: 1.xA0
AT Command: ATRE
AT Command: ATRN
Parameter Range: 0 - 3 [exponent]
Default Parameter Value: 0
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-01-0000-00FD4 | XLAMP XPG LED COMM WARM/NTRL WHT |
| OPB480T11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
| XPERDO-L1-0000-00A03 | XLAMP XP-E LED - RED-ORANGE |
| XPEHEW-L1-0000-00H50 | LED XLAMP XPE HIEFF WHITE SMD |
| OPB480P11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XBIB-R-DEV | 功能描述:界面开发工具 RS-232 XBee-PRO pro onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U | 功能描述:界面开发工具 USB XBee-PRO interf -PRO interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-DEV | 功能描述:界面开发工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SP | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SS | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。