- 您现在的位置：买卖IC网 > PDF目录18683 > XBIB-R (Digi International/Maxstream)BOARD RS232 ZIGBEE MOD PRO PDF资料下载
参数资料
| 型号： | XBIB-R |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 23/72页 |
| 文件大小： | 1116K |
| 描述： | BOARD RS232 ZIGBEE MOD PRO |
| 设计资源： | XBIB-R Schematic |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | XBee 和 XBee Pro 收音机 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
XBee/XBeePRO"燨EM燫F燤odules??02.15.4?爒1.xAx燵2007.05.031]
2007燤axStream,營nc.
牋牋?3
Chapter??燫F燤odule燨peration
Pin Doze (SM = 2)
"Pin/Host-controlled
" Typical power-down current: < 50 礎
" Wake-up time: 2 msec
Pin Doze Mode functions as does Pin Hibernate Mode; however, Pin Doze features faster wake-up
time and higher power consumption.
To wake a sleeping module operating in Pin Doze Mode, de-assert Sleep_RQ (pin 9). The module
will wake when Sleep_RQ is de-asserted and is ready to transmit or receive when the CTS
line is
low. When waking the module, the pin must be de-asserted at least two 'byte times' after CTS
goes low. This assures that there is time for the data to enter the DI buffer.
Cyclic Sleep Modes
Cyclic Sleep Remote (SM = 4)
" Typical Power-down Current: < 50 礎 (when asleep)
" Wake-up time: 2 msec
The Cyclic Sleep Modes allow modules to periodically check for RF data. When the SM parameter is
set to 4, the module is configured to sleep, then wakes once a cycle to check for data from a
module configured as a Cyclic Sleep Coordinator (SM = 0, CE = 1). The Cyclic Sleep Remote sends
a poll request to the coordinator at a specific interval set by the SP (Cyclic Sleep Period) parame-
ter. The coordinator will transmit any queued data addressed to that specific remote upon receiv-
ing the poll request.
If no data is queued for the remote, the coordinator will not transmit and the remote will return to
sleep for another cycle. If queued data is transmitted back to the remote, it will stay awake to
allow for back and forth communication until the ST (Time before Sleep) timer expires.
Also note that CTS
will go low each time the remote wakes, allowing for communication initiated
by the remote host if desired.
Cyclic Sleep Remote with Pin Wake-up (SM = 5)
Use this mode to wake a sleeping remote module through either the RF interface or by the de-
assertion of Sleep_RQ for event-driven communications. The cyclic sleep mode works as described
above (Cyclic Sleep Remote) with the addition of a pin-controlled wake-up at the remote module.
The Sleep_RQ pin is edge-triggered, not level-triggered. The module will wake when a low is
detected then set CTS
low as soon as it is ready to transmit or receive.
Any activity will reset the ST (Time before Sleep) timer so the module will go back to sleep only
after there is no activity for the duration of the timer. Once the module wakes (pin-controlled),
further pin activity is ignored. The module transitions back into sleep according to the ST time
regardless of the state of the pin.
[Cyclic Sleep Coordinator (SM = 6)]
" Typical current = Receive current
" Always awake
NOTE: The SM=6 parameter value exists solely for backwards compatibility with firmware version
1.x60. If backwards compatibility with the older firmware version is not required, always use the CE
(Coordinator Enable) command to configure a module as a Coordinator.
This mode configures a module to wake cyclic sleeping remotes through RF interfacing. The Coor-
dinator will accept a message addressed to a specific remote 16 or 64-bit address and hold it in a
buffer until the remote wakes and sends a poll request. Messages not sent directly (buffered and
requested) are called "Indirect messages". The Coordinator only queues one indirect message at a
time. The Coordinator will hold the indirect message for a period 2.5 times the sleeping period
indicated by the SP (Cyclic Sleep Period) parameter. The Coordinator's SP parameter should be set
to match the value used by the remotes.
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-01-0000-00FD4 | XLAMP XPG LED COMM WARM/NTRL WHT |
| OPB480T11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
| XPERDO-L1-0000-00A03 | XLAMP XP-E LED - RED-ORANGE |
| XPEHEW-L1-0000-00H50 | LED XLAMP XPE HIEFF WHITE SMD |
| OPB480P11Z | SWITCH PHOTOLOGIC SLOTTD OPTICAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XBIB-R-DEV | 功能描述:界面开发工具 RS-232 XBee-PRO pro onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U | 功能描述:界面开发工具 USB XBee-PRO interf -PRO interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-DEV | 功能描述:界面开发工具 USB XBee-PRO profes onal interface board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SP | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Pads RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XBIB-U-SS | 功能描述:界面开发工具 USB/Xbee/Xbee-Pro Inf Brd SMT Skt RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。