参数资料
| 型号： | XRD98L61AIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 26/38页 |
| 文件大小： | 0K |
| 描述： | IC CCD DIGITIZER 12BIT 48TQFP |
| 标准包装： | 250 |
| 位数： | 12 |
| 通道数： | 1 |
| 电压 - 电源，模拟： | 2.7 V ~ 3.6 V |
| 电压 - 电源，数字： | 2.7 V ~ 3.6 V |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
XRD98L61
32
Rev. 2.00
End of Line N
Start of Line N+1
Active Video
Pixels
OB pixels
Vertical Shift
Dummy &
OB pixels
CAL
Internal
DC restore time
CCD
Signal
Active Video pixels
t
CAL
4 pixels
CLAMP
(vertical shift)
Disconnect CDS from
input pins
Internal Black Level
calibration time
t
CAL - 4 pixels
Minimum 5 Pixels
Figure 22. Line Rate Timing with OneShot=1 & VSreject=1
SETTING POWER AND PERFORMANCE WITH Rext
The power and performance levels of the XRD98L61
are set by the value of Rext. Rext sets the current bias
level for the entire chip. Rext is connected between pin
39 (ExtRef) and analog ground (see Figure 23). This
resistor should be placed as close as possible to the
pin and routed directly to a ground plane in a PCB
layout.
A surface mount carbon resistor is recom-
mended.
Increasing values of Rext decrease the power, linearity
and noise performance of the XRD98L61. Lowering the
value of Rext increases linearity and noise perfor-
mance while increasing power.
The tested default
value for Rext is 30KOhms.
In order to match system to system performance and
set consistent manufacturable performance levels
between cameras, it is recommended that the Rext
resistor have <1% tolerance.
Digital-to-Analog Converters
There are two voltage output, 8-bit resolution, Digital-
to-Analog Converters (DACs) which can be used for a
variety of purposes, and are controlled via the serial
interface. On power up, these DACs are disabled. To
activate them, you must write a "0" to the DAC0pd and
DAC1pd bits in the Control register.
相关PDF资料 |
PDF描述 |
|---|---|
| XRD98L62ACV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRD98L63AIV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRT71D00IQ-F | IC JITTER ATTENUATOR SGL 32TQFP |
| XRT71D03IV-F | IC JITTER ATTENUATOR 3CH 64TQFP |
| XRT71D04IV | IC JITTER ATTENUATOR 4CH 80TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRD98L61EVAL | 功能描述:数据转换 IC 开发工具 Eval Board for XRD98L61AIV RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| XRD98L61ZEVAL | 功能描述:数据转换 IC 开发工具 Eval Board (Solder) XRD98L61AIV RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| XRD98L62 | 制造商:EXAR 制造商全称:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L62ACV | 制造商:EXAR 制造商全称:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L62ACV-F | 功能描述:视频 IC RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。