参数资料
型号: ZL2101ALAF
厂商: Intersil
文件页数: 23/27页
文件大小: 0K
描述: IC REG BUCK SYNC ADJ 6A 36QFN
标准包装: 50
类型: 降压(降压)
输出类型: 可调式
输出数: 1
输出电压: 0.54 V ~ 5.5 V
输入电压: 4.5 V ~ 14 V
PWM 型: 电压模式
频率 - 开关: 200kHz ~ 1MHz
电流 - 输出: 6A
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 36-VFQFN 裸露焊盘
包装: 托盘
供应商设备封装: 36-QFN(6x6)
ZL2101
TABLE 13. TRACKING MODE CONFIGURATION
R SS
(k Ω )
19.6
UVLO
(V)
TRACKING RATIO
(%)
UPPER TRACK LIMIT
Limited by target voltage
RAMP-UP/DOWN BEHAVIOR
Output not allowed to decrease before PG
21.5
23.7
26.1
28.7
31.6
34.8
38.3
56.2
61.9
68.1
75
82.5
90.9
100
5.5
7.5
100
50
100
50
Limited by VTRK pin voltage
Limited by target voltage
Limited by VTRK pin voltage
Limited by target voltage
Limited by VTRK pin voltage
Limited by target voltage
Limited by VTRK pin voltage
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
Output will always follow VTRK
Output not allowed to decrease before PG
110
I 2 C/SMBus Communications
The ZL2101 provides an I 2 C/SMBus digital interface that enables
the user to configure all aspects of the device operation as well
as monitor the input and output parameters. The ZL2101 can be
used with any standard 2-wire I 2 C host device.
In addition, the device is compatible with SMBus version 2.0 and
includes an SALRT line to help mitigate bandwidth limitations
related to continuous fault monitoring. Pull-up resistors are
required on the I 2 C/SMBus as specified in the SMBus 2.0
specification. The ZL2101 accepts most standard PMBus
commands. When controlling the device with PMBus commands,
it is recommended that the enable pin is tied to SGND.
I 2 C/SMBus Device Address Selection
When communicating with multiple devices using the
I 2 C/SMBus interface, each device must have its own unique
address so the host can distinguish between the devices. The
device address can be set according to the pin-strap options
listed in Table 14. Address values are right-justified.
TABLE 14. SMBUS DEVICE ADDRESS SELECTION
Output will always follow VTRK
Digital-DC Bus
The Digital-DC Communications (DDC) bus is used to
communicate between Zilker Labs Digital-DC devices. This
dedicated bus provides the communication channel between
devices for features such as sequencing and fault spreading. The
DDC pin on all Digital-DC devices in an application should be
connected together. A pull-up resistor is required on the DDC bus
in order to guarantee the rise time as expressed in Equation 16:
Rise Time = R PU ?C LOAD ≈ 1μs (EQ. 16)
Where R PU is the DDC bus pull-up resistance and C LOAD is the bus
loading. The pull-up resistor may be tied to VRA or to an external
3.3V or 5V supply as long as this voltage is present prior to or
during device power-up. As rules of thumb, each device
connected to the DDC bus presents approximately 10pF of
capacitive loading, and each inch of FR4 PCB trace introduces
approximately 2pF. The ideal design will use a central pull-up
resistor that is well matched to the total load capacitance. In
power module applications, the user should consider whether to
place the pull-up resistor on the module or on the PCB of the end
application.
SA PIN SETTING
LOW
OPEN
HIGH
SMBus ADDRESS
0x20
0x21
0x22
The minimum pull-up resistance should be limited to a value that
enables any device to assert the bus to a voltage that will ensure
a logic 0 (typically 0.8V at the device monitoring point) given the
pull-up voltage (5V if tied to VRA) and the pull-down current
capability of the ZL2101 (nominally 4mA).
If additional device addresses are required, a resistor can be
connected to the SA pin according to Table 15 to provide up to 30
unique device addresses.
23
FN7730.0
January 23, 2012
相关PDF资料
PDF描述
LQP03TN2N2B02D INDUCT 2.2NH+/-0.1NH 600MA 0201
CDRH5D18-5R4NC INDUCTOR 5.4UH SHIELDED SMD
GBM22DRMN-S273 CONN EDGECARD 44POS .156 SQ WW
MAX16074RS25D1+T IC MPU SUPERVISOR CIRCUIT 4UCSP
MAX16074RS25D0+T IC MPU SUPERVISOR CIRCUIT 4UCSP
相关代理商/技术参数
参数描述
ZL2101ALAFT 功能描述:IC REG BUCK SYNC ADJ 6A 36QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:两者兼有 输出数:1 输出电压:5V,1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP(0.154",3.90mm 宽) 包装:带卷 (TR) 供应商设备封装:16-QSOP
ZL2101ALAFTK 功能描述:IC REG BUCK SYNC ADJ 6A 36QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:两者兼有 输出数:1 输出电压:5V,1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP(0.154",3.90mm 宽) 包装:带卷 (TR) 供应商设备封装:16-QSOP
ZL2102 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:6A Digital Integrated Synchronous Step-Down DC/DC Regulator with Auto Compensation
ZL2102ALAFT7A 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 6A 36QFN 制造商:Intersil Corporation 功能描述:ZL2102 Series 14 V 6 A 1 MHz Surface Mount Digital DC-DC Converter - QFN-36 制造商:Intersil Corporation 功能描述:Voltage Regulators - Switching Regulators 6A Digital DC-DC Converter w/ DDC
ZL2102ALAFTK 制造商:Intersil Corporation 功能描述:6A DIGITAL DC-DC CONVERTER W/ DDC AND AUTO COMP- TR1K - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 6A 36QFN 制造商:Intersil Corporation 功能描述:DC-DC CONV, BUCK, ADJ, 1MHZ, QFN-36, Primary Input Voltage:14V, No. of Outputs:1