参数资料
型号: 71M6531D-IM/F
厂商: TERIDIAN SEMICONDUCTOR CORP
元件分类: 电源管理
英文描述: 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68
封装: LEAD FREE, QFN-68
文件页数: 64/120页
文件大小: 2477K
代理商: 71M6531D-IM/F
Data Sheet 71M6531D/F-71M6532D/F
FDS 6531/6532 005
48
2005-2010 TERIDIAN Semiconductor Corporation
v1.3
Table 48: EECTRL Bits for the 3-Wire Interface
Control
Bit
Name
Read/
Write
Description
7
WFR
W
Wait for Ready. If this bit is set, the trailing edge of BUSY will be delayed
until a rising edge is seen on the data line. This bit can be used during
the last byte of a Write command to cause the INT5 interrupt to occur
when the EEPROM has finished its internal write sequence. This bit is
ignored if HiZ = 0.
6
BUSY
R
Asserted while the serial data bus is busy. When the BUSY bit falls, an
INT5 interrupt occurs.
5
HiZ
W
Indicates that the SD signal is to be floated to high impedance immediately
after the last SCK rising edge.
4
RD
W
Indicates that EEDATA is to be filled with data from EEPROM.
3:0
CNT[3:0]
W
Specifies the number of clocks to be issued. Allowed values are 0
through 8. If RD=1, CNT bits of data will be read MSB first and right
justified into the low order bits of EEDATA. If RD=0, CNT bits will be sent
MSB first to the EEPROM, shifted out of the MSB of EEDATA. If
CNT[3:0] is zero, SDATA will simply obey the HiZ bit.
The timing diagrams in Figure 11 through Figure 15 describe the 3-wire EEPROM interface behavior. All
commands begin when the EECTRL register is written. Transactions start by first raising the DIO pin that
is connected to CS. Multiple 8-bit or less commands such as those shown in Figure 11 through Figure 15
are then sent via EECTRL and EEDATA.
When the transaction is finished, CS must be lowered. At the end of a Read transaction, the EEPROM
will be driving SDATA, but will transition to HiZ (high impedance) when CS falls. The firmware should
then immediately issue a write command with CNT=0 and HiZ=0 to take control of SDATA and force it to
a low-Z state.
Figure 11: 3-Wire Interface. Write Command, HiZ=0
Figure 12: 3-Wire Interface. Write Command, HiZ=1
SCLK (output)
BUSY (bit)
CNT Cycles (6 shown)
SDATA (output)
Write -- No HiZ
D2
D3
D4
D5
D6
D7
EECTRL Byte Written
INT5
SDATA output Z
(LoZ)
CNT Cycles (6 shown)
Write -- With HiZ
INT5
EECTRL Byte Written
SCLK (output)
BUSY (bit)
SDATA (output)
D2
D3
D4
D5
D6
D7
(HiZ)
(LoZ)
SDATA output Z
相关PDF资料
PDF描述
71M6532F-IGTR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100
71M6534-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP120
71M6534H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP120
71M6533H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6534-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP120
相关代理商/技术参数
参数描述
71M6531D-IMR/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6531D-IMR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6531D-IMR/F2 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6531F 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6531F-DB 功能描述:开发板和工具包 - 8051 71M6531F Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: