参数资料
| 型号： | 71M6531F-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 45/121页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 71M6531F |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | 71M6531 |
| 主要属性： | 单相功率表 |
| 已供物品： | 2 个板，线缆，CD，电源 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页
FDS 6531/6532 005
Data Sheet 71M6531D/F-71M6532D/F
Additionally, if DIO6 and DIO7 are configured as DIO and defined as outputs, they can be used as
dedicated pulse outputs (WPULSE = DIO6, VARPULSE = DIO7) using the DIO_PW and DIO_PV bits. In
this case, DIO6 and DIO7 are under CE control. DIO4 and DIO5 can be configured to implement the
EEPROM Interface.
The PB pin is a dedicated digital input. In addition, if the optical UART is not used, OPT_TX and OPT_RX
can be configured as dedicated DIO pins, DIO1 and DIO2, respectively (see Section 1.5.6 Optical Interface ).
The internal control resources selectable for the DIO pins are listed in Table 46 . If more than one input is
connected to the same resource, the resources are combined using a logical OR.
Tracking DIO pins configured as outputs is useful for pulse counting without external hardware.
Either the interrupts or the counter/timer clocks can be used to count pulses on the pulse outputs
or interrupts on the CE’s power failure output.
When driving LEDs, relay coils etc., the DIO pins should sink the current into GNDD (as shown in
Figure 10 , right), not source it from V3P3D (as shown in Figure 10 , left). This is due to the resis-
tance of the internal switch that connects V3P3D to either V3P3SYS or VBAT.
Sourcing current into or out of DIO pins other than the PB pin, for example with pull-up or pull-
down resistors, should be avoided. Violating this rule will lead to increased quiescent current in
SLEEP and LCD modes.
HIGH
HIGH-Z
LOW
MISSION
LCD/SLEEP
BROWNOUT
V3P3SYS
VBAT
V3P3D
DIO
GNDD
HIGH
HIGH-Z
LOW
MISSION
LCD/SLEEP
BROWNOUT
V3P3SYS
VBAT
V3P3D
DIO
GNDD
Figure 10: Connecting an External Load to DIO Pins
1.5.10 LCD Drivers – 71M6531D/F
The 71M6531 contains a total of 39 dedicated and multiplexed LCD drivers which are grouped as follows:
? 11 dedicated LCD segment drivers – always available
? 3 drivers multiplexed with the ICE interface (E_TCLK, E_RST, E_RXTX) – available in normal operation
mode (when not emulating)
? 2 driver multiplexed with auxiliary signals MUX_SYNC and CKTEST (SEG7, SEG19) – available
when not used for test
? 4 drivers multiplexed with the SPI port (PCLK, PSDO, PCSZ, PSDI)
? 4 common drivers for multiplexing (25%, 33%, 50%, or 100% duty cycle) – always available
With a minimum of 16 driver pins always available and a total of 39 driver pins in the maximum configuration,
the device is capable of driving between 64 to 156 pixels of LCD display with 25% duty cycle. At eight pixels
per digit, this corresponds to 8 to 19 digits. At 33% duty cycle, 48 to 117 pixels can be driven.
For each multi-use pin, the corresponding LCD_BITMAP[] bit (see Section 1.5.7 Digital I/O – 71M6531D/F ),
is used to select the pin for DIO or LCD operation. The mapping of the LCD_BITMAP[] bits is specified in
Rev 2
45
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6533-DB | BOARD DEMO 71M6533 |
| 71M6534H-DB | BOARD DEMO 71M6534H |
| 71M6541F-DB | DEMO BOARD 71M6541F |
| 71M6543F-DB-CT | DEMO BOARD 71M6543F-DB-CT |
| 72-CNV-5 | CONVERTER RS-232 TO RS-422 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6531F-IM/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6531F-IM/F3 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6531F-IM/F4 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6531F-IM/FR4 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6531F-IMR/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。