收藏本站
参数资料
型号： 73S1210F-68IMR/F/P
厂商： Maxim Integrated Products
文件页数： 35/126页
文件大小： 0K
描述： IC SMART CARD READER PROG 68-QFN
产品培训模块： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装： 2,500
系列： 73S12xx
核心处理器： 80515
芯体尺寸： 8-位
速度： 24MHz
连通性： I²C，智能卡，UART/USART
外围设备： LED，POR，WDT
输入/输出数： 8
程序存储器容量： 32KB（32K x 8）
程序存储器类型： 闪存
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 6.5 V
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 68-VFQFN 裸露焊盘
包装： 带卷 (TR)
73S1210F Data Sheet
DS_1210F_001
16
Rev. 1.4
1.4
Program Security
Two levels of program and data security are available. Each level requires a specific fuse to be blown in
order to enable or set the specific security mode. Mode 0 security is enabled by setting the SECURE bit
(bit 6 of SFR register FLSHCTL 0xB2). Mode 0 limits the ICE interface to only allow bulk erase of the
flash program memory. All other ICE operations are blocked. This guarantees the security of the user’s
MPU program code. Security (Mode 0) is enabled by MPU code that sets the SECURE bit. The MPU
code must execute the setting of the SECURE bit immediately after a reset to properly enable Mode 0.
This should be the first instruction after the reset vector jump has been executed. If the “startup.a51”
assembly file is used in an application, then it must be modified to set the SECURE bit after the reset
vector jump. If not using “startup.a51”, then this should be the first instruction in main(). Once security
Mode 0 is enabled, the only way to disable it is to perform a global erase of the flash followed by a full
circuit reset. Once the flash has been erased and the reset has been executed, security Mode 0 is
disabled and the ICE has full control of the core. The flash can be reprogrammed after the bulk erase
operation is completed. Global erase of the flash will also clear the data XRAM memory.
The security enable bit (SECURE) is reset whenever the MPU is reset. Hardware associated with the bit
only allows it to be set. As a result, the code may set the SECURE bit to enable the security Mode 0
feature but may not reset it. Once the SECURE bit is set, the code is protected and no external read of
program code in flash or data (in XRAM) is possible. In order to invoke the security Mode 0, the
SECSET0 (bit 1 of the XRAM SFR register SECReg 0xFFD7) fuse must be blown beforehand or the
security mode 0 will not be enabled. The SECSET0 and SECSET1 fuses once blown, cannot be
overridden.
Specifically, when SECURE is set:
The ICE is limited to bulk flash erase only.
Page zero of flash memory, the preferred location for the user’s preboot code, may not be page-
erased by either MPU or ICE. Page zero may only be erased with global flash erase. Note that
global flash erase erases XRAM whether the SECURE bit is set or not.
Writes to page zero, whether by MPU or ICE, are inhibited.
Security mode 1 is in effect when the SECSET1 fuse has been programmed (blown open). In security
mode 1, the ICE is completely and permanently disabled. The Flash program memory and the MPU are
not available for alteration, observation, nor control. As soon as the fuse has been blown, the ICE is
disabled. The testing of the SECSET1 fuse will occur during the reset and before the start of pre-boot
and boot cycles. This mode is not reversible, nor recoverable. In order to blow the SECSET1 fuse, the
SEC pin must be held high for the fuse burning sequence to be executed properly. The firmware can
check to see if this pin is held high by reading the SECPIN bit (bit 5 of XRAM SFR register SECReg
0xFFD7). If this bit is set and the firmware desires, it can blow the SECSET1 fuse. The burning of the
SECSET0 does not require the SEC pin to be held high.
In order to blow the fuse for SECSET1 and SECSET0, a particular set of register writes in a specific order
need to be followed. There are two additional registers that need to have a specific value written to them
in order for the desired fuse to be blown. These registers are FUSECtl (0xFFD2) and TRIMPCtl
(0xFFD1). The sequence for blowing the fuse is as follows:
1.
Write 0x54H to FUSECtl.
2.
Write 0x81H for security mode 0.
Note: only program one security mode at a time.
Write 0x82H for security mode 1.
Note: SEC pin must be high for security mode 1.
3.
Write 0xA6 to TRIMPCtl.
4.
Delay about 500 s.
5.
Write 0x00 to TRIMPCtl and FUSECtl.
相关PDF资料
PDF描述
73S1215F-68IMR/F/P IC SMART CARD READER PROG 68-QFN
73S1217F-68IMR/F/P IC SMART CARD READER PROG 68-QFN
73S1217F-68MR/F/PE IC SOC SMART CARD READER 68QFN
73S8010C-ILR/F IC SMART CARD INTERFACE 28-SOIC
73S8010R-ILR/F IC SMART CARD INTERFACE 28-SOIC
相关代理商/技术参数
参数描述
73S1210F-68M/F/PB 制造商:Maxim Integrated Products 功能描述:- Trays
73S1210F-68M/F/PG 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
73S1210F-68M/F/PH 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
73S1210F-68M/F/PJ 制造商:Maxim Integrated Products 功能描述:SCR+PPAD/SRL INTFC/PWR MGT-3.11CODE - Rail/Tube
73S1210F-68MR/F/PG 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*