- 您现在的位置：买卖IC网 > Datasheet目录306 > A3944KLPTR-T (Allegro Microsystems Inc)IC PREDRIVER MOSFET 6CH TSSOP Datasheet资料下载
参数资料
| 型号： | A3944KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 21/31页 |
| 文件大小： | 0K |
| 描述： | IC PREDRIVER MOSFET 6CH TSSOP |
| 标准包装： | 8,000 |
| 配置： | 低端 |
| 输入类型： | 并行/串行 |
| 延迟时间： | 200ns |
| 电流 - 峰： | 50mA |
| 配置数： | 6 |
| 输出数： | 6 |
| 电源电压： | 6 V ~ 40 V |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
A3944
Automotive, Low Side FET Pre-Driver
Applications Information
Drain Feedback Clamp Resistor Selection
The drain feedback input, DRNx, for each channel is clamped
internally with a 50 V (nominal) Zener diode. If the voltage
applied to this terminal is likely to exceed 50 V then an external
current limit resistor will be required to limit the current, power,
and energy to less than the Absolute Maximum specifications in
this document.
Note that the internal drain clamp in the A3944 is not intended to
dissipate the energy from any external load. The internal clamp
is provided to protect the internal circuits of the A3944 from any
high voltage that would otherwise cause permanent damage.
If the voltage at DRNx, V DRNx , will never exceed the minimum
drain clamp voltage, V DCL , then no external resistor is required
and DRNx can be connected directly to the drain of the external
MOSFET switch.
These values would typically apply to a remote load which is
primarily resistive. The load inductance will be due to a combina-
tion of the wiring and any parasitic inductance in the load. In this
example, the DC on-state current will be 13 V / 26 Ω = 0.5 A.
When the load is switched off, the inductance attempts to keep
the current flowing by increasing the voltage at the end connect
to the FET switch. This voltage increases up to the breakdown
voltage of the FET. At that point, the voltage across the load
amounts to the difference between the FET breakdown voltage
and the supply voltage, and it acts to reduce the current. With the
parameters in this example, the current would decay to zero in
less than 1 μ s. This is less than the 1.85 μ s limit for maximum
current, so the drain resistor will be based only on the maximum
current. The value of the drain resistor, R Dx , in this case is simply
the voltage across the resistor divided by the maximum current:
Three Absolute Maximum specifications apply to the A3944,
none of which may be exceeded:
R Dx =
V FET – V DCL
I DRNC
(1)
? The maximum clamp current, I DRNC , applies to very short
pulses, typically less than 1.85 μ s. Any current pulse less than
1.85 μ s and less than I DRNC , will never exceed the maximum
power or energy limits.
? The maximum clamp energy, E DRNC , applies to pulses between
1.85 μ s and 2 ms. Above 2 ms the heat produced by the clamp
energy dissipates through the silicon and the package; in that
case, the maximum clamp power applies. Note that for pulse
lengths between about 500 μ s and 2 ms the energy starts to dis-
where
V FET is the FET breakdown voltage,
V DCL is the A3944 drain clamp voltage, and
I DRNC is the A3944 drain clamp max current.
Substituting into equation 1:
sipate during the pulse, so the maximum current that is possible
will actually be higher than that calculated using the maximum
energy limit.
R Dx =
80 V – 54 V
100 mA
= 260 Ω
? The maximum clamp power, P DRNC , applies to pulses lasting
longer than 2 ms up to continuous operation.
The energy injected into the A3944 drain clamp is:
E DRNC = V DCL × I DRNC × t PULSE
(2)
Maximum current example:
? Load resistance: 26 Ω
? Load inductance: 130 μ H
? Load current: 0.5 A
? Load supply voltage: 13 V
? FET clamp voltage: 80 V
where t PULSE is the duration of the current pulse.
Substituting into equation 2:
E DRNC = 54 V × 100 mA × 0.9 μ s = 4.86 μ J (per pulse)
As expected, based on the pulse length, this is less than half the
clamp energy limit, given in the Absolute Maximum table.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
21
相关PDF资料 |
PDF描述 |
|---|---|
| A3985SLDTR-T | IC MOSFET DRVR PROG DUAL 38TSSOP |
| A4933KJPTR-T | IC PREDRIVER MOSFET 3PH 48LQFP |
| A4935KJPTR-T | IC MOSFET DVR AUTO 3PH 48-LQFP |
| A4940KLPTR-T | IC MOSF DVR FULL BRIDGE 24TSSOP |
| A6210GEUTR-T | IC LED DRIVER HIGH BRIGHT 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3946 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Half-Bridge Power MOSFET Controller |
| A3946GLPTR-T | 制造商:Allegro MicroSystems LLC 功能描述: |
| A3946KLB | 功能描述:IC CTRLR MOSFET 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3946KLB-T | 功能描述:IC MOSFET CONTROLLER 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3946KLBTR | 功能描述:IC CTRLR MOSFET 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
发布紧急采购，3分钟左右您将得到回复。