- 您现在的位置：买卖IC网 > PDF目录1773 > A3981KLPTR-T (Allegro Microsystems Inc)IC MOTOR DVR MICROSTEP 28-TSSOP PDF资料下载
参数资料
| 型号： | A3981KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 12/43页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DVR MICROSTEP 28-TSSOP |
| 标准包装： | 1 |
| 系列： | * |
| 应用： | * |
| 输出数： | * |
| 电流 - 输出： | * |
| 电压 - 负载： | * |
| 电源电压： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 620-1458-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
A3981
Automotive, Programmable Stepper Driver
Hot Warning If the chip temperature rises above the Hot Tem-
perature Warning Threshold, T JWH , the Fault flag will go low and
the Hot Warning bits will be set in the diagnostic registers. No
action will be taken by the A3981. When the temperature drops
below the Hot Temperature Warning Threshold, the Fault flag
will go high but the Hot Warning bits remain set in the diagnostic
registers until reset.
Cold Warning If the chip temperature falls below the Cold
Temperature Warning Threshold, T JWC , the Fault flag will go low
and the Cold Warning bits will be set in the diagnostic registers.
No action will be taken by the A3981. When the temperature rises
above the Cold Temperature Warning Threshold, the Fault flag
will go high but the Cold Warning bits remain set in the diagnos-
tic registers until reset.
Overtemperature Shutdown If the chip temperature rises
above the Overtemperature Shutdown Threshold, T JF , the Fault
flag will go low and the Thermal Shutdown bits will be set in the
diagnostic registers. The A3981 will disable the outputs to try to
prevent a further increase in the chip temperature. When the tem-
perature drops below the Overtemperature Shutdown Threshold,
the Fault flag will go high but the Thermal Shutdown bits remain
set in the diagnostic registers until reset.
Bridge and Output Diagnostics
The A3981 includes monitors that can detect a short to supply or
a short to ground at the motor phase connections. These condi-
tions are detected by monitoring the current from the motor
phase connections through the bridge to the motor supply and to
ground.
Low current comparators and timers are provided to help detect
possible open load conditions.
Short to Supply A short from any of the motor connections to
the motor supply (VBBA or VBBB) is detected by monitoring the
voltage across the low-side current sense resistor in each bridge.
This gives a direct measurement of the current through the low
side of the bridge.
When a low-side FET is in the On state, the voltage across the
sense resistor, under normal operating conditions, should never
be more than the Maximum Sense Voltage, V SMAX . In this state,
an overcurrent is determined to exist when the voltage across the
sense resistor exceeds the Low-Side Overcurrent Sense Voltage,
V OCL , typically 2 × V SMAX . This overcurrent must be continu-
ously present for at least the Overcurrent Fault Delay, t SCT ,
before the short fault is confirmed by setting the relevant bit in
FAULT0 and driving the DIAG output low if the Fault Output
flag is selected. The output is switched off and remains off until a
fault reset occurs.
Note that the sense resistor cannot distinguish which low-side
FET is in an overcurrent state. So, if more than one low-side FET
is active when the fault is detected, for example during low-side
recirculation with synchronous rectification, then the shorted con-
nection is determined from the internal PWM state.
The actual overcurrent that V OCL represents is determined by the
value of the sense resistor and is typically 2 × I SMAX .
Short to Ground A short from any of the motor connections
to ground is detected by directly monitoring the current through
each of the high-side FETs in each bridge.
When a high-side FET is in the On state the maximum current
is typically always less than 1 A. In this state, an overcurrent is
determined to exist when the current through the active high-side
FET exceeds the High-Side Overcurrent Threshold, I OCH .
This overcurrent must be present for at least the Overcurrent
Fault Delay, t SCT , before the short fault is confirmed by setting
the relevant bit in FAULT0 and driving the DIAG output low if
the Fault Output flag is selected. The output is switched off and
remains off until a fault reset occurs.
Note that when a short to ground is present the current through
the high-side FET is limited to the High-Side Current Limit,
I LIMH , during the Overcurrent Fault Delay, t SCT . This prevents
large negative transients at the phase output pins when the out-
puts are switched off.
Shorted Load A short across the load is indicated by concurrent
short faults on both high side and low side.
Short Fault Blanking All overcurrent conditions are ignored
for the duration of the Overcurrent Fault Delay, t SCT . The short
detection delay timer is started when an overcurrent first occurs.
If the overcurrent is still present at the end of the short detection
delay time then a short fault will be generated and latched. If the
overcurrent goes away before the short detection delay time is
complete, then the timer is reset and no fault is generated.
This prevents false short detection caused by supply and load
transients. It also prevents false short detections resulting from
current transients generated by the motor or wiring capacitance
when a FET is first switched on.
Short Fault Reset and Retry When a short circuit has been
detected all outputs for the faulty phase are disabled until the
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| A3982SLB-T | IC MOTOR DRIVER STEPPER 24-SOIC |
| A3983SLP-T | IC MICRO STEPPING DRIVER 24-TSSO |
| A3984SLP-T | IC MICRO STEPPING DRIVER 24-TSSO |
| A3986SLDTR-T | IC DRIVER MICROSTEPPING 38-TSSOP |
| A3987SLPTR-T | IC DRIVER MICROSTEPPING 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3982 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Stepper Motor Driver with Translator |
| A3982_13 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Stepper Motor Driver with Translator |
| A3982SLB | 功能描述:IC MOTOR DRIVER STEPPER 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3982SLB-T | 功能描述:IC MOTOR DRIVER STEPPER 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3982SLB-T | 制造商:Allegro MicroSystems 功能描述:Motor Driver IC |
发布紧急采购，3分钟左右您将得到回复。