- 您现在的位置：买卖IC网 > PDF目录1773 > A3981KLPTR-T (Allegro Microsystems Inc)IC MOTOR DVR MICROSTEP 28-TSSOP PDF资料下载
参数资料
| 型号： | A3981KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 31/43页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DVR MICROSTEP 28-TSSOP |
| 标准包装： | 1 |
| 系列： | * |
| 应用： | * |
| 输出数： | * |
| 电流 - 输出： | * |
| 电压 - 负载： | * |
| 电源电压： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 620-1458-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
A3981
Layout
Traces
Automotive, Programmable Stepper Driver
together externally. The copper ground plane located under the
exposed thermal pad is typically used as the star ground point.
R S ?
PCBThe printed circuit board (PCB, or printed wiring board)
should use a higher weight copper thickness than a standard small
signal or digital circuit board. This helps to reduce the impedance
of the printed traces when conducting high currents. PCB traces
carrying switching currents should be as wide and short as pos-
sible to reduce the inductance of the trace. This will help reduce
any voltage transients caused by current switching during PWM
current control.
For optimum thermal performance, the exposed thermal pad on
the underside of the A3981 should be soldered directly onto the
board. A solid ground plane should be added to the opposite side
of the board, and multiple vias through the board to the ground
plane should be placed in the area under the thermal pad.
Decoupling
All supplies should be decoupled with an electrolytic capacitor in
parallel with a ceramic capacitor. The ceramic capacitor should
have a value of 100 nF and should be placed as close as pos-
sible to the associated supply and ground pins of the A3981. The
electrolytic capacitor connected to VBB should be rated at least
Current Sense Resistor
In sensing the output current level, to minimize inaccuracies
caused by ground-trace IR drops, the current sense resistor (R S )
should have an independent ground return to the star ground
point. This path should be as short as possible. For low-value
sense resistors, the IR drop in the PCB trace to the sense resis-
tor can be significant and should be taken into account. Surface
mount chip resistors are recommended to minimize contact
resistance and parasitic inductance. The value, R S , of the sense
resistor is given by:
V REF
16 ? I SMAX
There is no restriction on the value of R S or V REF , other than the
range of V REF over which the output current precision is guaran-
teed. However, it is recommended that the value of V REF be kept
as high as possible to improve the current accuracy. The table
below provides increasing values of I SMAX for suggested values
of V REF and standard E96 values of R S .
Suggested Values
1.5 times the maximum circuit voltage, and selected to support
the maximum ripple current provided to the motor. The value of
the capacitor is unimportant but should be the lowest value with
the necessary ripple current capability.
The pump capacitor between CP1 and CP2, the pump storage
capacitor between VCP and VBB, and the compensation capaci-
tor between VREG and ground should be connected as close as
possible to the respective pins of the A3981.
Grounding
A star ground system, with the common star point located close to
the A3981, is recommended. The reference ground, AGND (pin
7), and the power ground, PGND (pin 21), must be connected
I SMAX
(mA)
100
200
300
405
501
610
702
812
912
1008
R S
(m Ω )
499
499
417
309
249
205
178
154
137
124
V REF
(V)
0.8
1.6
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
31
相关PDF资料 |
PDF描述 |
|---|---|
| A3982SLB-T | IC MOTOR DRIVER STEPPER 24-SOIC |
| A3983SLP-T | IC MICRO STEPPING DRIVER 24-TSSO |
| A3984SLP-T | IC MICRO STEPPING DRIVER 24-TSSO |
| A3986SLDTR-T | IC DRIVER MICROSTEPPING 38-TSSOP |
| A3987SLPTR-T | IC DRIVER MICROSTEPPING 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3982 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Stepper Motor Driver with Translator |
| A3982_13 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Stepper Motor Driver with Translator |
| A3982SLB | 功能描述:IC MOTOR DRIVER STEPPER 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3982SLB-T | 功能描述:IC MOTOR DRIVER STEPPER 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3982SLB-T | 制造商:Allegro MicroSystems 功能描述:Motor Driver IC |
发布紧急采购，3分钟左右您将得到回复。