- 您现在的位置：买卖IC网 > PDF目录1980 > AD7190BRUZ-REEL (Analog Devices Inc)IC ADC 2CH 24BIT W/PGA 24TSSOP PDF资料下载
参数资料
| 型号： | AD7190BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/41页 |
| 文件大小： | 0K |
| 描述： | IC ADC 2CH 24BIT W/PGA 24TSSOP |
| 设计资源： | Precision Weigh Scale Design Using AD7190 with Internal PGA (CN0102) |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 4.8k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个差分，双极；4 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
Data Sheet
AD7190
Rev. C | Page 25 of 40
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0(0)
BPDSW(0)
GP32EN(0)
GP10EN(0)
P3DAT(0)
P2DAT(0)
P1DAT(0)
P0DAT(0)
Table 21. Register Bit Designations
Bit Location
Bit Name
Description
GP7
0
This bit must be programmed with a Logic 0 for correct operation.
GP 6
BPDSW
Bridge power-down switch control bit. This bit is set by the user to close the bridge power-down switch
BPDSW to AGND. The switch can sink up to 30 mA. The bit is cleared by the user to open the bridge power-
down switch. When the ADC is placed in power-down mode, the bridge power-down switch remains active.
GP5
GP32EN
Digital Output P3 and Digital Output P2 enable. When GP32EN is set, the digital outputs, P3 and P2, are
active. When GP32EN is cleared, the P3 and P2 pins are tristated, and the P3DAT and P2DAT bits are ignored.
GP4
GP10EN
Digital Output P1 and Digital Output P0 enable. When GP10EN is set, the digital outputs, P1 and P0, are
active. When GP10EN is cleared, the P1 and P0 outputs are tristated, and the P1DAT and P0DAT bits are
ignored. The P1 and P0 pins can be used as a reference input REFIN2 when the REFSEL bit in the
configuration register is set to 1.
GP3
P3DAT
Digital Output P3. When GP32EN is set, the P3DAT bit sets the value of the P3 general-purpose output pin.
When P3DAT is high, the P3 output pin is high. When P3DAT is low, the P3 output pin is low. When the
GPOCON register is read, the P3DAT bit reflects the status of the P3 pin if GP32EN is set.
GP2
P2DAT
Digital Output P2. When GP32EN is set, the P2DAT bit sets the value of the P2 general-purpose output pin.
When P2DAT is high, the P2 output pin is high. When P2DAT is low, the P2 output pin is low. When the
GPOCON register is read, the P2DAT bit reflects the status of the P2 pin if GP32EN is set.
GP1
P1DAT
Digital Output P1. When GP10EN is set, the P1DAT bit sets the value of the P1 general-purpose output pin.
When P1DAT is high, the P1 output pin is high. When P1DAT is low, the P1 output pin is low. When the
GPOCON register is read, the P1DAT bit reflects the status of the P1 pin if GP10EN is set.
GP0
P0DAT
Digital Output P0. When GP10EN is set, the P0DAT bit sets the value of the P0 general-purpose output pin.
When P0DAT is high, the P0 output pin is high. When P0DAT is low, the P0 output pin is low. When the
GPOCON register is read, the P0DAT bit reflects the status of the P0 pin if GP10EN is set.
OFFSET REGISTER
(RS2, RS1, RS0 = 1, 1, 0; Power-On/Reset = 0x800000)
The offset register holds the offset calibration coefficient for the
ADC. The power-on reset value of the offset register is 0x800000.
The AD7190 has four offset registers; therefore, each channel
has a dedicated offset register. Each of these registers is a 24-bit
read/write register. This register is used in conjunction with its
associated full-scale register to form a register pair. The power-
on reset value is automatically overwritten if an internal or
system zero-scale calibration is initiated by the user. The AD7190
must be placed in power-down mode or idle mode when writing
to the offset register.
FULL-SCALE REGISTER
(RS2, RS1, RS0 = 1, 1, 1; Power-On/Reset = 0x5XXXX0)
The full-scale register is a 24-bit register that holds the full-scale
calibration coefficient for the ADC. The AD7190 has four full-
scale registers; therefore, each channel has a dedicated full-scale
register. The full-scale registers are read/write registers. However,
when writing to the full-scale registers, the ADC must be placed
in power-down mode or idle mode. These registers are configured
at power-on with factory-calibrated, full-scale calibration coef-
ficients, the calibration being performed at gain = 1. Therefore,
every device has different default coefficients. The default value
is automatically overwritten if an internal or system full-scale
calibration is initiated by the user or if the full-scale register is
written to.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7191BRUZ | IC ADC 2CH 24B SD 24TSSOP |
| AD7192BRUZ | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7190WBRUZ | 功能描述:24 Bit Analog to Digital Converter 2, 4 Input 1 Sigma-Delta 24-TSSOP 制造商:analog devices inc. 系列:- 包装:管件 零件状态:有效 位数:24 采样率（每秒）:4.8k 输入数:2，4 输入类型:差分，个伪差分 数据接口:SPI，DSP 配置:MUX-PGA-ADC 无线电 - S/H:ADC:- A/D 转换器数:1 架构:三角积分 参考类型:外部， 内部 电压 - 电源，模拟:5V 电压 - 电源，数字:2.7 V ~ 5.25 V 特性:PGA，温度传感器 工作温度:-40°C ~ 105°C 封装/外壳:24-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:24-TSSOP 标准包装:1 |
| AD7190WBRUZ-RL | 制造商:Analog Devices 功能描述: |
| AD7191 | 制造商:AD 制造商全称:Analog Devices 功能描述:Pin-Programmable, Ultralow Noise, 24-Bit, Sigma-Delta ADC for Bridge Sensors |
| AD7191A/0B | 制造商:Sony Nec Optiarc America 功能描述:DOUBLE DUAL INTERNAL DVDRW PATA BEZEL 20X/18X12XRAM - Bulk |
| AD7191BRUZ | 功能描述:IC ADC 2CH 24B SD 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。