- 您现在的位置：买卖IC网 > PDF目录1980 > AD7190BRUZ-REEL (Analog Devices Inc)IC ADC 2CH 24BIT W/PGA 24TSSOP PDF资料下载
参数资料
| 型号： | AD7190BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/41页 |
| 文件大小： | 0K |
| 描述： | IC ADC 2CH 24BIT W/PGA 24TSSOP |
| 设计资源： | Precision Weigh Scale Design Using AD7190 with Internal PGA (CN0102) |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 4.8k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个差分，双极；4 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
Data Sheet
AD7190
Rev. C | Page 35 of 40
SYSTEM SYNCHRONIZATION
The SYNC input allows the user to reset the modulator and the
digital filter without affecting any of the setup conditions on the
part. This allows the user to start gathering samples of the analog
input from a known point in time, that is, the rising edge of
SYNC. SYNC needs to be taken low for four master clock cycles
to implement the synchronization function.
If multiple AD7190 devices are operated from a common master
clock, they can be synchronized so that their data registers are
updated simultaneously. A falling edge on the SYNC pin resets
the digital filter and the analog modulator and places the AD7190
into a consistent, known state. While the SYNC pin is low, the
AD7190 is maintained in this state. On the SYNC rising edge,
the modulator and filter are taken out of this reset state and, on
the next clock edge, the part starts to gather input samples again.
In a system using multiple AD7190 devices, a common signal to
their SYNC pins synchronizes their operation. This is normally
done after each AD7190 has performed its own calibration or
has had calibration coefficients loaded into its calibration
registers. The conversions from the AD7190s are then
synchronized.
The part is taken out of reset on the master clock falling edge
following the SYNC low-to-high transition. Therefore, when
multiple devices are being synchronized, the SYNC pin should
be taken high on the master clock rising edge to ensure that all
devices begin sampling on the master clock falling edge. If the
SYNC pin is not taken high in sufficient time, it is possible to
have a difference of one master clock cycle between the devices;
that is, the instant at which conversions are available differs
from part to part by a maximum of one master clock cycle.
The SYNC pin can also be used as a start conversion command.
In this mode, the rising edge of SYNC starts conversion, and the
falling edge of RDY indicates when the conversion is complete.
The disadvantage of this scheme is that the settling time of the
filter has to be allowed for each data register update. This means
that the rate at which the data register is updated is reduced. For
example, if the ADC is configured to use the sinc4 filter, zero
latency is disabled and chop is disabled, the data register update
takes four times longer.
TEMPERATURE SENSOR
Embedded in the AD7190 is a temperature sensor. This is
selected using the CH2 bit in the configuration register. When
the CH2 bit is set to 1, the temperature sensor is enabled. When
the temperature sensor is selected and bipolar mode is selected,
the device should return a code of 0x800000 when the temper-
ature is 0 K. A one-point calibration is needed to get the optimum
performance from the sensor. Therefore, a conversion at 25°C
should be recorded and the sensitivity calculated. The sensitivity
is approximately 2815 codes/°C. The equation for the temperature
sensor is
Temp (K) = (Conversion – 0x800000)/2815 K
Temp (°C) = Temp (K) – 273
Following the one point calibration, the internal temperature
sensor has an accuracy of ±2 °C, typically.
BRIDGE POWER-DOWN SWITCH
In bridge applications such as strain gauges and load cells, the
bridge itself consumes the majority of the current in the system.
For example, a 350 Ω load cell requires 15 mA of current when
excited with a 5 V supply. To minimize the current consumption
of the system, the bridge can be disconnected (when it is not
being used) using the bridge power-down switch. Figure 18
shows how the bridge power-down switch is used. The switch
can withstand 30 mA of continuous current, and it has an on
resistance of 10 Ω maximum.
LOGIC OUTPUTS
The AD7190 has four general-purpose digital outputs, P0, P1,
P2, and P3. These are enabled using the GP32EN and GP10EN
bits in the GPOCON register. The pins can be pulled high or
low using the P0DAT to P3DAT bits in the GPOCON register;
that is, the value at the pin is determined by the setting of the
P0DAT to P3DAT bits. The logic levels for these pins are
determined by AVDD rather than by DVDD. When the GPOCON
register is read, the P0DAT to P3DAT bits reflect the actual
value at the pins. This is useful for short-circuit detection.
These pins can be used to drive external circuitry, for example,
an external multiplexer. If an external multiplexer is used to
increase the channel count, the multiplexer logic pins can be
controlled via the AD7190 general-purpose output pins. The
general-purpose output pins can be used to select the active
multiplexer pin. Because the operation of the multiplexer is
independent of the AD7190, the AD7190 modulator and filter
should be reset using the SYNC pin each time that the multi-
plexer channel is changed.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7191BRUZ | IC ADC 2CH 24B SD 24TSSOP |
| AD7192BRUZ | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7190WBRUZ | 功能描述:24 Bit Analog to Digital Converter 2, 4 Input 1 Sigma-Delta 24-TSSOP 制造商:analog devices inc. 系列:- 包装:管件 零件状态:有效 位数:24 采样率（每秒）:4.8k 输入数:2，4 输入类型:差分，个伪差分 数据接口:SPI，DSP 配置:MUX-PGA-ADC 无线电 - S/H:ADC:- A/D 转换器数:1 架构:三角积分 参考类型:外部， 内部 电压 - 电源，模拟:5V 电压 - 电源，数字:2.7 V ~ 5.25 V 特性:PGA，温度传感器 工作温度:-40°C ~ 105°C 封装/外壳:24-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:24-TSSOP 标准包装:1 |
| AD7190WBRUZ-RL | 制造商:Analog Devices 功能描述: |
| AD7191 | 制造商:AD 制造商全称:Analog Devices 功能描述:Pin-Programmable, Ultralow Noise, 24-Bit, Sigma-Delta ADC for Bridge Sensors |
| AD7191A/0B | 制造商:Sony Nec Optiarc America 功能描述:DOUBLE DUAL INTERNAL DVDRW PATA BEZEL 20X/18X12XRAM - Bulk |
| AD7191BRUZ | 功能描述:IC ADC 2CH 24B SD 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。