- 您现在的位置：买卖IC网 > PDF目录10182 > AD7851KRZ (Analog Devices Inc)IC ADC 14BIT SRL 333KSPS 24-SOIC PDF资料下载
参数资料
| 型号： | AD7851KRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/36页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SRL 333KSPS 24-SOIC |
| 标准包装： | 31 |
| 位数： | 14 |
| 采样率（每秒）： | 333k |
| 数据接口： | 8051，QSPI?，串行，SPI? µP |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极；1 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD7851
–20–
REV. B
POWER-UP TIMES
Using an External Reference
When the AD7851 is powered up, the part is powered up
from one of two conditions: first, when the power supplies
are initially powered up and; secondly, when the parts are
powered up from either a hardware or software power-down
(see previous section).
When AVDD and DVDD are powered up, the AD7851 enters a
mode whereby the
CONVST signal initiates a timeout followed
by a self-calibration. The total time taken for this timeout and
calibration is approximately 35 ms (see the Automatic Calibra-
tion on Power-On section). During power-up, the functionality
of the
SLEEP pin is disabled, that is, the part will not power
down until the end of the calibration if
SLEEP is tied logic low.
The power-up calibration mode can be disabled if the user
writes to the control register before a
CONVST signal is applied. If
the timeout and self-calibration are disabled, then the user
must take into account the time required by the AD7851 to
power up before a self-calibration is carried out. This power-up
time is the time taken for the AD7851 to power up when
power is first applied (300
s typ), or the time it takes the exter-
nal reference to settle to the 14-bit level—whichever is longer.
The AD7851 powers up from a full hardware or software
power-down in 5
s typ. This limits the throughput which the
part is capable of to 120 kSPS for the K Grade and 126 kSPS
for the A Grade when powering down between conversions.
Figure 24 shows how power-down between conversions is
implemented using the
CONVST pin. The user first selects
the power-down between conversions option by using the
SLEEP pin and the power management bits, PMGT1 and
PMGT0, in the control register (see previous section). In this
mode, the AD7851 automatically enters a full power-down at
the end of a conversion, that is, when BUSY goes low. The
falling edge of the next
CONVST pulse causes the part to
power up. Assuming the external reference is left powered up,
the AD7851 should be ready for normal operation 5
s after
this falling edge. The rising edge of
CONVST initiates a con-
version so the
CONVST pulse should be at least 5
s wide.
The part automatically powers down on completion of the
conversion. Where the software convert start is used, the part
may be powered up in software before a conversion is initiated.
5 s
3.25 s
tCONVERT
POWER-UP
TIME
NORMAL
OPERATION
FULL
POWER-DOWN
POWER-UP
TIME
START CONVERSION ON RISING EDGE
POWER UP ON FALLING EDGE
CONVST
BUSY
Figure 24. Using the
CONVST Pin to Power Up for
a Conversion
Using the Internal (On-Chip) Reference
As in the case of an external reference, the AD7851 can power
up from one of two conditions: power up after the supplies are
connected or power up from a hardware/software power-down.
When using the on-chip reference and powering up when AVDD
and DVDD are first connected, it is recommended that the
power-up calibration mode be disabled as explained previously.
When using the on-chip reference, the power-up time is effec-
tively the time it takes to charge up the external capacitor on the
REFIN/REFOUT pin. This time is given by the equation
tUP = 9
× R × C
where R
≈ 150K and C = external capacitor.
The recommended value of the external capacitor is 100 nF;
this gives a power-up time of approximately 135 ms before a
calibration is initiated and normal operation should commence.
When CREF is fully charged, the power-up time from a hardware or
software power-down reduces to 5
s. This is because an internal
switch opens to provide a high impedance discharge path for the
reference capacitor during power-down—see Figure 25. An added
advantage of the low charge leakage from the reference capacitor
during power-down is that even though the reference is being pow-
ered down between conversions, the reference capacitor holds the
reference voltage to within 0.5 LSBs with throughput rates of 100
samples/second and over with a full power-down between conver-
sions. A high input impedance op amp, such as the AD707, should
be used to buffer this reference capacitor if it is being used exter-
nally. Note, if the AD7851 is left in its powered-down state for
more than 100 ms, the charge on CREF will start to leak away and
the power-up time will increase. If this long power-up time is a
problem, the user can use a partial power-down for the last conver-
sion so the reference remains powered up.
AD7851
REFIN/REFOUT
EXTERNAL
CAPACITOR
SWITCH OPENS
DURING POWER-DOWN
BUF
ON-CHIP
REFERENCE
TO OTHER
CIRCUITRY
Figure 25. On-Chip Reference During Power-Down
POWER VS. THROUGHPUT RATE
The main advantage of a full power-down after a conversion is
that it significantly reduces the power consumption of the part
at lower throughput rates. When using this mode of operation,
the AD7851 is only powered up for the duration of the conver-
sion. If the power-up time of the AD7851 is taken to be 5
s
and it is assumed that the current during power up is 12 mA
typ, then power consumption as a function of throughput can
easily be calculated. The AD7851 has a conversion time of
3.25
s with a 6 MHz external clock. This means the AD7851
consumes 12 mA typ for 8.25
s in every conversion cycle if the
parts are powered down at the end of a conversion. The graph
in Figure 26 shows the power consumption of the AD7851 as a
function of throughput. Table VII lists the power consump-
tion for various throughput rates.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-25F-CU-F2 | CONVERTER MOD DC/DC 72V 200W |
| VE-2TP-MY | CONVERTER MOD DC/DC 13.8V 50W |
| MS27497E20B41P | CONN RCPT 41POS WALL MNT W/PINS |
| VE-2TN-MY | CONVERTER MOD DC/DC 18.5V 50W |
| VE-25D-IW-S | CONVERTER MOD DC/DC 85V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7851KRZ3 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
| AD7851KRZ-REEL | 功能描述:IC ADC 14BIT SRL 333KSPS 24-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7851KRZ-REEL3 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
| AD7853 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| AD7853AN | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 24-Pin PDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 24PDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:SELF CAL.SERIAL 12-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
发布紧急采购，3分钟左右您将得到回复。