参数资料
型号: AD7851KRZ
厂商: Analog Devices Inc
文件页数: 21/36页
文件大小: 0K
描述: IC ADC 14BIT SRL 333KSPS 24-SOIC
标准包装: 31
位数: 14
采样率(每秒): 333k
数据接口: 8051,QSPI?,串行,SPI? µP
转换器数目: 2
功率耗散(最大): 89.25mW
电压电源: 模拟和数字
工作温度: 0°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SOIC(0.295",7.50mm 宽)
供应商设备封装: 24-SOIC W
包装: 管件
输入数目和类型: 1 个伪差分,单极;1 个伪差分,双极
AD7851
–28–
REV. B
If the user has control of the
CONVST pin but does not want to
exercise it for every conversion, the control register may be used
to start a conversion. Setting the
CONVST bit in the control
register to 1 starts a conversion. If the user does not have con-
trol of the
CONVST pin, a conversion should not be initiated
by writing to the control register. The reason for this is that the
user may get locked out and not be able to perform any further
write/read operations. When a conversion is started by writing to
the control register, the
SYNC goes low and read/write opera-
tions take place while the conversion is in progress. However,
once the conversion is complete, there is no way of writing to
the part unless the
CONVST pin is exercised. The CONVST
signal triggers the
SYNC signal low which allows read/write
operations to take place.
SYNC must be low to perform read/
write operations. The
SYNC is triggered low by the CONVST
signal rising edge or by setting the
CONVST bit in the control
register to 1. Therefore, if there is not full control of the
CONVST pin, the user may become locked out.
SERIAL
INTERFACE
MODE
?
POWER ON, APPLY CLKIN SIGNAL,
WAIT FOR AUTOMATIC CALIBRATION
DIN CONNECTED TO DGND
NO
YES
START
WAIT FOR BUSY SIGNAL
TO GO LOW
PULSE
CONVST PIN
READ
DATA
DURING
CONVERSION
?
WAIT APPROXIMATELY 200ns
AFTER
CONVST RISING EDGE
APPLY
SYNC (IF REQUIRED), SCLK, AND READ
CONVERSION RESULT ON DOUT PIN
PULSE
CONVST PIN
SYNC AUTOMATICALLY GOES LOW
AFTER
CONVST RISING EDGE
SCLK AUTOMATICALLY ACTIVE, READ
CONVERSION RESULT ON DOUT PIN
4, 5
2, 3
Figure 40. Flowchart for Setting Up and Reading from the AD7851
CONFIGURING THE AD7851
AD7851 as a Read-Only ADC
The AD7851 contains 14 on-chip registers that can be accessed
via the serial interface. In the majority of applications, it will not
be necessary to access all of these registers. Figure 40 outlines the
sequence used to configure the AD7851 as a read-only ADC. In
this case, there is no writing to the on-chip registers and only the
conversion result data is read from the part. Interface Mode 1
cannot be used in this case as it is necessary to write to the con-
trol register to set Interface Mode 1. Here the CLKIN signal is
applied directly after power-on; the CLKIN signal must be
present to allow the part to perform a calibration. This automatic
calibration will be completed approximately 42 ms after the
AD7851 has powered up (6 MHz CLK).
相关PDF资料
PDF描述
VE-25F-CU-F2 CONVERTER MOD DC/DC 72V 200W
VE-2TP-MY CONVERTER MOD DC/DC 13.8V 50W
MS27497E20B41P CONN RCPT 41POS WALL MNT W/PINS
VE-2TN-MY CONVERTER MOD DC/DC 18.5V 50W
VE-25D-IW-S CONVERTER MOD DC/DC 85V 100W
相关代理商/技术参数
参数描述
AD7851KRZ3 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter
AD7851KRZ-REEL 功能描述:IC ADC 14BIT SRL 333KSPS 24-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率(每秒):300k 数据接口:并联 转换器数目:1 功率耗散(最大):75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC(0.295",7.50mm 宽) 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端,单极;1 个单端,双极
AD7851KRZ-REEL3 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter
AD7853 制造商:AD 制造商全称:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs
AD7853AN 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 24-Pin PDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 24PDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:SELF CAL.SERIAL 12-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs