- 您现在的位置：买卖IC网 > PDF目录10182 > AD7851KRZ (Analog Devices Inc)IC ADC 14BIT SRL 333KSPS 24-SOIC PDF资料下载
参数资料
| 型号： | AD7851KRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/36页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SRL 333KSPS 24-SOIC |
| 标准包装： | 31 |
| 位数： | 14 |
| 采样率（每秒）： | 333k |
| 数据接口： | 8051，QSPI?，串行，SPI? µP |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极；1 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
–21–
REV. B
AD7851
Table VII. Power Consumption vs. Throughput
Throughput Rate
Power AD7851
1 kSPS
9 mW
2 kSPS
18 mW
THROUGHPUT RATE (Hz)
100
10
0.01
0
2000
200
1
400
600
800 1000 1200 1400 1600 1800
0.1
POWER
(mW)
Figure 26. Power vs. Throughput AD7851
NOTE
When setting the power-down mode by writing to the part,
operating in an interface mode other than Interface Modes 4
and 5 is recommended. This way the user has more control to
initiate power-down and power-up commands.
CALIBRATION SECTION
Calibration Overview
The automatic calibration that is performed on power-up ensures
that the calibration options covered in this section will not be
required for a significant number of applications. The user will
not have to initiate a calibration unless the operating conditions
change (CLKIN frequency, analog input mode, reference voltage,
temperature, and supply voltages). The AD7851 has a number of
calibration features that may be required in some applications,
and there are a number of advantages in performing these differ-
ent types of calibration. First, the internal errors in the ADC can
be reduced significantly to give superior dc performance; and
second, system offset and gain errors can be removed. This allows
the user to remove reference errors (whether internal or external
references) and to make use of the full dynamic range of the
AD7851 by adjusting the analog input range of the part for a
specific system.
The AD7851 has two main calibration modes: self-calibration
and system calibration. There are various options in both self-
calibration and system calibration as outlined previously in
Table III. All the calibration functions can be initiated by puls-
ing the
CAL pin or by writing to the control register and setting
the STCAL bit to 1. The timing diagrams that follow involve
using the
CAL pin.
The duration of each of the different types of calibrations is
given in Table VIII for the AD7851 with a 6 MHz/7 MHz mas-
ter clock. These calibration times are master-clock dependent.
Table VIII. Calibration Times (AD7851 with 6 MHz CLKIN)
Type of Self- or System Calibration
Time (ms)
Full
41.7
Gain + Offset
9.26
Offset
4.63
Gain
4.63
Automatic Calibration on Power-On
The
CAL pin has a 0.15
A pull-up current source connected to it
internally to allow for an automatic full self-calibration on power-
on. A full self-calibration will be initiated on power-on if a 10 nF
capacitor is connected from the
CAL pin to DGND. The internal
current source connected to the
CAL pin charges up the external
capacitor and the time required to charge the external capacitor
will depend on the size of the capacitor itself. This time should be
large enough to ensure that the internal reference is settled before
the calibration is performed. However, if an external reference is
being used, this reference must have stabilized before the auto-
matic calibration is initiated (a larger capacitor on the
CAL pin
should be used if the external reference has not settled when the
autocalibration is initiated). Once the capacitor on the
CAL pin
has charged, the calibration will be performed and will take 32 ms
(4 MHz CLKIN). Therefore, the autocalibration should be com-
plete before operating the part. After calibration, the part is accu-
rate to the 12-bit level and the specifications quoted on the data
sheet apply. There will be no need to perform another calibra-
tion unless the operating conditions change or unless a system
calibration is required.
Self-Calibration Description
There are a four different calibration options within the self-
calibration mode. There is a full self-calibration where the
DAC, internal offset, and internal gain errors are calibrated
out; there is (Gain + Offset) self-calibration which calibrates
out the internal gain error and then the internal offset errors
(the internal DAC is not calibrated here); and finally, there are
self-offset and self-gain calibrations that calibrate out the inter-
nal offset errors and the internal gain errors, respectively.
The internal capacitor DAC is calibrated by trimming each of the
capacitors in the DAC. It is the ratio of these capacitors to each
other that is critical, and so the calibration algorithm ensures
that this ratio is at a specific value by the end of the calibration
routine. For the offset and gain there are two separate capaci-
tors, one of which is trimmed when an offset or gain calibration
is performed. Again, it is the ratio of these capacitors to the
capacitors in the DAC that is critical and the calibration algo-
rithm ensures that this ratio is at a specified value for both
the offset and gain calibrations.
In bipolar mode, the midscale error is adjusted for an offset cali-
bration and the positive full-scale error is adjusted for the gain
calibration; in unipolar mode, the zero-scale error is adjusted for
an offset calibration and the positive full-scale error is adjusted
for a gain calibration.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-25F-CU-F2 | CONVERTER MOD DC/DC 72V 200W |
| VE-2TP-MY | CONVERTER MOD DC/DC 13.8V 50W |
| MS27497E20B41P | CONN RCPT 41POS WALL MNT W/PINS |
| VE-2TN-MY | CONVERTER MOD DC/DC 18.5V 50W |
| VE-25D-IW-S | CONVERTER MOD DC/DC 85V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7851KRZ3 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
| AD7851KRZ-REEL | 功能描述:IC ADC 14BIT SRL 333KSPS 24-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7851KRZ-REEL3 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
| AD7853 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| AD7853AN | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Serial 24-Pin PDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT SERL 24PDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:SELF CAL.SERIAL 12-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
发布紧急采购，3分钟左右您将得到回复。