参数资料
| 型号： | AD9146BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/56页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SRL DUAL 48LFCSP |
| 标准包装： | 1 |
| 系列： | TxDAC+® |
| 设置时间： | 20ns |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-WQ（7x7） |
| 包装： | 托盘 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 1.23G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
AD9146
Data Sheet
Rev. A | Page 38 of 56
PLL SETTINGS
Three settings for the PLL circuitry should be programmed to
their nominal values. The PLL values shown in Table 21 are the
recommended settings for these parameters.
Table 21. PLL Settings
PLL Control Register
Register
Address
Bits
Optimal
Setting
PLL Loop Bandwidth[1:0]
0x0C
[7:6]
11
PLL Charge Pump Current[4:0]
0x0C
[4:0]
10001
PLL Cross-Control Enable
0x0D
4
1
CONFIGURING THE VCO TUNING BAND
The PLL VCO has a valid operating range from approximately
1.0 GHz to 2.1 GHz covered in 63 overlapping frequency bands.
For any desired VCO output frequency, there may be several
valid PLL band select values. The frequency bands of a typical
device are shown in Figure 49. Device-to-device variations and
operating temperature affect the actual band frequency range.
Therefore, it is required that the optimal PLL band select value
be determined for each individual device.
0
4
8
12
16
20
24
28
32
36
40
44
48
52
56
60
1000
2200
2000
1800
1600
1400
1200
P
L
BAND
VCO FREQUENCY (MHz)
09691-
054
Figure 49. PLL Lock Range over Temperature for a Typical Device
Automatic VCO Band Select
The device has an automatic VCO band select feature on chip.
Using the automatic VCO band select feature is a simple and
reliable method of configuring the VCO frequency band. This
feature is enabled by starting the PLL in manual mode, then
placing the PLL in auto band select mode. This is done by
setting Register 0x0A to a value of 0xCF, then to a value of
0xA0. When these values are written, the device executes an
automated routine that determines the optimal VCO band
setting for the device. The setting selected by the device ensures
that the PLL remains locked over the full 40°C to +85°C
operating temperature range of the device without further
adjustment. (The PLL remains locked over the full temperature
range even if the temperature during initialization is at one of
the temperature extremes.)
Manual VCO Band Select
The device also has a manual band select mode (PLL manual
enable, Register 0x0A, Bit 6 = 1) that allows the user to select
the VCO tuning band. In manual mode, the VCO band is set
directly with the value written to the manual VCO band bits
(Register 0x0A, Bits[5:0]). To properly select the VCO band,
follow these steps:
1. Put the device in manual band select mode by setting
Register 0x0A, Bit 6 = 1.
2. Sweep the VCO band over a range of bands that results in
the PLL being locked.
3. For each band, verify that the PLL is locked and read the
PLL using the VCO control voltage bits (Register 0x0E,
Bits[3:0]).
4. Select the band that results in the control voltage being
closest to the center of the range, that is, 1001 or 1000 (see
Table 22). The resulting VCO band should be the optimal
setting for the device. Write this value to the manual VCO
band bits (Register 0x0A, Bits[5:0]).
5. If desired, an indication of where the VCO is within the
operating frequency band can be determined by querying
the VCO control voltage. Table 22 shows how to interpret
the PLL VCO control voltage value (Register 0x0E, Bits[3:0]).
Table 22. VCO Control Voltage Range Indications
VCO Control Voltage
(Register 0x0E, Bits[3:0])
Indication
1111
Move to higher VCO band
1110
1101
VCO is operating in the higher end
of the frequency band
1100
1011
1010
1001
VCO is operating within an optimal
region of the frequency band
1000
0111
0110
0101
VCO is operating in the lower end
of the frequency band
0100
0011
0010
0001
Move to lower VCO band
0000
相关PDF资料 |
PDF描述 |
|---|---|
| GTC02R-36-5P | CONN RCPT 4POS BOX MNT W/PINS |
| VE-2TY-MX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| MS27508E24B4PC | CONN RCPT 56POS BOX MNT W/PINS |
| VE-2TY-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| MS27508E24B4PB | CONN RCPT 56POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9146BCPZRL | 功能描述:IC DAC 16BIT SRL DUAL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9146-EBZ | 制造商:Analog Devices 功能描述:16 BIT DUAL SIGNAL PROC DAC EB - Boxed Product (Development Kits) |
| AD9146-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9146 DAC RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148ARUZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。