参数资料
| 型号： | AD9146BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 46/56页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SRL DUAL 48LFCSP |
| 标准包装： | 1 |
| 系列： | TxDAC+® |
| 设置时间： | 20ns |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-WQ（7x7） |
| 包装： | 托盘 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 1.23G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
AD9146
Data Sheet
Rev. A | Page 50 of 56
INTERFACE TIMING VALIDATION
The AD9146 provides on-chip sample error detection (SED)
circuitry that simplifies verification of the input data interface.
The SED circuitry compares the input data samples captured at
the digital input pins with a set of comparison values. The
comparison values are loaded into registers through the SPI
port. Differences between the captured values and the compar-
ison values are detected and stored. Options are available for
customizing SED test sequencing and error handling.
SED OPERATION
The SED circuitry operates on a data set made up of four 16-bit
input words divided into eight 8-bit input words, denoted as I0,
Q0, I1, and Q1. To properly align the input samples, the first I
data-word (that is, I0) is indicated by asserting FRAME for at
least one complete input sample.
Figure 69 shows the input timing of the interface in byte mode.
The FRAME signal can be issued once at the start of the data
transmission, or it can be asserted repeatedly at intervals coinciding
with the I0 and Q0 data-words.
FRAME
DATA
I0MSB
I0LSB
Q0MSB
Q0LSB
I1MSB
I1LSB
Q1MSB
Q1LSB
09691-
075
Figure 69. Timing Diagram of Extended FRAME Signal Required to Align
Input Data for SED
The SED has three flag bits (Register 0x67, Bit 5, Bit 1, and
Bit 0) that indicate the results of the input sample comparisons.
The sample error detected bit (Register 0x67, Bit 5) is set when
an error is detected and remains set until cleared. The SED also
provides registers that indicate which input data bits experienced
errors (Register 0x70 through Register 0x73). These bits are latched
and indicate the accumulated errors detected until cleared.
Autosample error detection (AED) is an autoclear function in the
SED. The autoclear mode has two effects: it activates the compare
fail bit and the compare pass bit (Register 0x67, Bit 1 and Bit 0) and
changes the behavior of Register 0x70 through Register 0x73. The
compare pass bit is set if the last eight sample set comparisons
are error free. The compare fail bit is set if an error is detected.
The compare fail bit is not activated until the part has received
eight error-free sample set comparisons, that is, the pass bit has
gone high at least once. Once enabled, the compare fail bit is
automatically cleared by the reception of eight consecutive error-
free comparisons. When autoclear mode is enabled, Register 0x70
through Register 0x73 accumulate errors as previously described
but are reset to all 0s after eight consecutive error-free sample
set comparisons are made.
If desired, the sample error detected, compare pass, and compare
fail flags can be configured to trigger the IRQ pin when active.
This is done by enabling the appropriate bits in the event flag
register (Register 0x07).
Table 26 shows a progression of the input sample comparison
results and the corresponding states of the error flags.
Table 26. Progression of Input Sample Comparison Results and the Resulting SED Register Values
Compare Results (Pass/Fail)
P
F
P
F
P
F
Register 0x67, Bit 5 (Sample Error Detected)
0
1
Register 0x67, Bit 1 (Compare Fail)
0
1
Register 0x67, Bit 0 (Compare Pass)
1
0
1
0
Register 0x70 to Register 0x73
(Errors Detected Bits)
1
Z = all 0s.
2
N = nonzero.
相关PDF资料 |
PDF描述 |
|---|---|
| GTC02R-36-5P | CONN RCPT 4POS BOX MNT W/PINS |
| VE-2TY-MX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| MS27508E24B4PC | CONN RCPT 56POS BOX MNT W/PINS |
| VE-2TY-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| MS27508E24B4PB | CONN RCPT 56POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9146BCPZRL | 功能描述:IC DAC 16BIT SRL DUAL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9146-EBZ | 制造商:Analog Devices 功能描述:16 BIT DUAL SIGNAL PROC DAC EB - Boxed Product (Development Kits) |
| AD9146-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9146 DAC RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148ARUZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。