参数资料
| 型号： | AD9146BCPZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/56页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SRL DUAL 48LFCSP |
| 标准包装： | 2,500 |
| 系列： | TxDAC+® |
| 设置时间： | 20ns |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-WQ（7x7） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 1.23G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Data Sheet
AD9146
Rev. A | Page 49 of 56
INTERRUPT REQUEST OPERATION
The AD9146 provides an interrupt request output signal on
Pin 34 (IRQ) that can be used to notify an external host processor
of significant device events. Upon assertion of the interrupt, the
device should be queried to determine the precise event that
occurred. The IRQ pin is an open-drain, active low output. Pull
the IRQ pin high external to the device. This pin can be tied to
the interrupt pins of other devices with open-drain outputs to
wire-OR these pins together.
The event flags provide visibility into the device. These flags
are located in the two event flag registers, Register 0x06 and
Register 0x07. The behavior of each event flag is independently
selected in the interrupt enable registers, Register 0x04 and
Register 0x05. When the flag interrupt enable is active, the
event flag latches and triggers an external interrupt. When the
flag interrupt is disabled, the event flag monitors the source
signal, but the IRQ pin remains inactive.
Figure 68 shows the IRQ-related circuitry and how the event
flag signals propagate to the IRQ output. The INTERRUPT_
ENABLE signal represents one bit from the interrupt enable
register. The EVENT_FLAG_SOURCE signal represents one bit
from the event flag register. The EVENT_ FLAG_SOURCE
signal represents one of the device signals that can be monitored,
such as the PLL_LOCKED signal from the PLL phase detector
or the FIFO_WARNING_1 signal from the FIFO controller.
When an interrupt enable bit is set high, the corresponding event
flag bit reflects a positively tripped version of the EVENT_FLAG_
SOURCE signal; that is, the event flag bit is latched on the rising
edge of the EVENT_FLAG_SOURCE signal. This signal also
asserts the external IRQ pin.
When an interrupt enable bit is set low, the event flag bit reflects
the current status of the EVENT_FLAG_SOURCE signal, and
the event flag has no effect on the external IRQ pin.
The latched version of an event flag (the INTERRUPT_SOURCE
signal) can be cleared in two ways. The recommended way is by
writing 1 to the corresponding event flag bit. A hardware or soft-
ware reset also clears the INTERRUPT_SOURCE signal.
INTERRUPT SERVICE ROUTINE
Interrupt request management starts by selecting the set of
event flags that require host intervention or monitoring. The
events that require host action should be enabled so that the
host is notified when they occur. For events requiring host
intervention upon IRQ activation, run the following routine
to clear an interrupt request:
1. Read the status of the event flag bits that are being
monitored.
2. Set the interrupt enable bit low so that the unlatched
EVENT_FLAG_SOURCE signal can be monitored directly.
3. Perform any actions that may be required to clear the
EVENT_FLAG_SOURCE. In many cases, no specific
actions may be required.
4. Read the event flag to verify that the actions taken have
cleared the EVENT_FLAG_SOURCE.
5. Clear the interrupt by writing 1 to the event flag bit.
6. Set the interrupt enable bits of the events to be monitored.
Note that some EVENT_FLAG_SOURCE signals are latched
signals. These signals are cleared by writing to the correspond-
ing event flag bit. For more information about each event flag,
see Register 0x06 and Register 0x07 in Table 11.
INTERRUPT_ENABLE
EVENT_FLAG_SOURCE
DEVICE_RESET
EVENT_FLAG
INTERRUPT_
SOURCE
1
0
OTHER
INTERRUPT
SOURCES
IRQ
WRITE_1_TO_EVENT_FLAG
09691-
074
Figure 68. Simplified Schematic of IRQ Circuitry
相关PDF资料 |
PDF描述 |
|---|---|
| AD9267BCPZ | IC MOD SIGMA-DELTA DUAL 64LFCSP |
| AD9272BSVZRL-80 | IC ADC ASD OCTAL 80MSPS 100-TQFP |
| AD9273BBCZ-50 | IC ADCASD OCTAL 25MSPS 144CSPBGA |
| AD9276BSVZ | IC ADC 12BIT LNA/VGA/AAF 100TQFP |
| AD9277BSVZ | IC ADC 14BIT LNA/VGA/AAF 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9146-EBZ | 制造商:Analog Devices 功能描述:16 BIT DUAL SIGNAL PROC DAC EB - Boxed Product (Development Kits) |
| AD9146-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9146 DAC RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148ARUZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
| AD9148BBCZ | 功能描述:IC DAC 16BIT QD 1GSPS 196CSPBGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
发布紧急采购，3分钟左右您将得到回复。