- 您现在的位置：买卖IC网 > PDF目录10069 > AD9627ABCPZ-80 (Analog Devices Inc)IC ADC 12BIT 80MSPS 64LFCSP PDF资料下载
参数资料
| 型号： | AD9627ABCPZ-80 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 38/76页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 80MSPS 64LFCSP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 80M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 490mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
AD9627
Rev. B | Page 43 of 76
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit locations.
The memory map is roughly divided into four sections: the chip
configuration registers (Address 0x00 to Address 0x02); the
channel index and transfer registers (Address 0x05 and
Address 0xFF); the ADC functions registers, including setup,
control, and test (Address 0x08 to Address 0x25); and the digital
feature control registers (Address 0x100 to Address 0x11B).
The memory map register table (see Table 25) documents the
default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the
default hexadecimal value given. For example, Address 0x18,
the VREF select register, has a hexadecimal default value of 0xC0.
This means that Bit 7 = 1, Bit 6 = 1, and the remaining bits are 0s.
This setting is the default reference selection setting. The default
value uses a 2.0 V p-p reference. For more information on this
function and others, see Application Note AN-877, Interfacing to
High Speed ADCs via SPI. This document details the functions
controlled by Register 0x00 to Register 0xFF. The remaining
registers, from Register 0x100 to Register 0x11B, are documented
in the Memory Map Register Description section.
Open Locations
All address and bit locations that are not included in Table 25
are not currently supported for this device. Unused bits of a
valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open (for example, Address 0x13), this address location should
not be written.
Default Values
After the AD9627 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table, Table 25.
Logic Levels
An explanation of logic level terminology follows:
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simulta-
neously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and the bit autoclears.
Channel-Specific Registers
Some channel setup functions, such as the signal monitor
thresholds, can be programmed differently for each channel.
In these cases, channel address locations are internally duplicated
for each channel. These registers and bits are designated in Table 25
as local. These local registers and bits can be accessed by setting
the appropriate Channel A or Channel B bits in Register 0x05.
If both bits are set, the subsequent write affects the registers of
both channels. In a read cycle, only Channel A or Channel B
should be set to read one of the two registers. If both bits are set
during an SPI read cycle, the part returns the value for Channel A.
Registers and bits designated as global in Table 25 affect the
entire part or the channel features where independent settings are
not allowed between channels. The settings in Register 0x05 do
not affect the global registers and bits.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BNL-IV-F3 | CONVERTER MOD DC/DC 28V 150W |
| IDT7205L12PDG | IC FIFO 8192X9 12NS 28PDIP |
| VE-BNJ-IV-F3 | CONVERTER MOD DC/DC 36V 150W |
| VE-BNJ-IV-F2 | CONVERTER MOD DC/DC 36V 150W |
| VE-BNF-IV-F3 | CONVERTER MOD DC/DC 72V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9627BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9627BCPZ11-105 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD9627BCPZ11-150 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD9627BCPZ-125 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD9627BCPZ-150 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 150Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP 制造商:Analog Devices 功能描述:ADC Dual Pipelined 150Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP Tray |
发布紧急采购，3分钟左右您将得到回复。