参数资料
| 型号： | ADATE207BBPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/36页 |
| 文件大小： | 0K |
| 描述： | IC TIMING FORMATTER QUAD 256BGA |
| 标准包装： | 1 |
| 类型： | 四针定时格式器 |
| PLL： | 是 |
| 主要目的： | 自动测试设备 |
| 电路数： | 4 |
| 频率 - 最大： | 100MHz |
| 电源电压： | 2.375 V ~ 2.625 V |
| 工作温度： | -25°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-LBGA 裸露焊盘 |
| 供应商设备封装： | 256-BGA（27x27） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADATE207
Rev. 0 | Page 15 of 36
M
PER_EARLY_T0EN
PER_EARLY_C0EN
MCLK
INPUT DELAY[7:0]
CE
DQ
T0 PIPELINE
M
TIMING
GENERATOR
M
05
55
7-
0
04
Figure 10. INPUT_DELAY Pipeline
Figure 11 shows the timing of PER_EARLY_T0EN and
the associated period delay offset, INPUT_DELAY. The
INPUT_DELAY signal is added to each programmed delay
across all channels. This input delay can change for each
PER_EARLY_T0EN period.
The delay from the pattern inputs to the DUT is four T0
pipeline delays, plus four MCLK pipeline delays, plus
approximately 27.5 ns of analog delay, plus any programmed
delay as shown in Figure 8.
The delay from the pattern inputs to the fail outputs is eight
PER_EARLY_T0EN periods plus the programmed T0
alignment pipeline depth.
DUT CAPTURE
Each compare event can strobe the state of the dual comparators
signals for each pin. These are resynchronized to T0 periods
and output for use in mixed signal capture applications. There
are four DUT capture pins per channel, PAT_DUTDATA_x and
each can be configured to output the high or low comparators
of each of the four possible compare events.
TMU MULTIPLEXER
The ADATE207 supports time measurement via an external
time measurement unit (TMU) in the following configurations:
Connect the high comparator output of any pin to
TMU_ARM, TMU_START, or TMU_STOP.
Connect the low comparator output of any pin to
TMU_ARM, TMU_START, or TMU_STOP.
The time measurement unit select logic provides time and
frequency measurement capability from the high or low
comparator outputs of any digital pin. To accomplish this
task, independent multiplexers direct the high and low
comparator outputs of the digital pins to the time measurement
unit signals, TMU_ARM, TMU_START, and TMU_STOP. Off-
chip control logic must select the appropriate TMU bus output
signal from the ADATE207 and direct its selection to the TMU.
The TMU outputs are high speed, differential 8 mA drivers and
can be tristated for bus applications.
LOW JITTER CLOCK DRIVER
The ADATE207 has 2-to-1 multiplexers in the DR_DATA_CH3
and DR_DATA_CH2 output drivers to allow an external low
jitter clock signal to drive the DCL. This feature is not available
on the DR_DATA_CH0 and DR_DATA_CH1 outputs.
CLOCK GENERATOR MODE
The ADATE207 incorporates a clock generation mode to allow
it to be used as a programmable clock generator. In this mode, it
is possible for each of the four channels to produce an
independently programmable clock.
To activate this mode, PER_EARLY_T0EN and the
CLKGEN_MD_EN input need to be set high. In this mode,
PAT_DATA_VALID has no effect. The pattern data signals
(PAT_PATDATA_x) are interpreted as period offsets and the
PAT_MASK[x] inputs are used as period start enables. See
Table 11 for details of signal mapping. The use model for this
mode is
Program drive high/drive low operations at Address 0 in
the waveform memory. Depending on the delays, the value
per edge, the duty cycle, and the start level can be adjusted
per channel
Four different clocks can be controlled by using
PAT_MASK[N] as equivalent period start signals for an
individual Channel N.
Skew/insertion delay of the clocks can be adjusted
individually by using I_PAT_PATADATA_N as an
INPUT_DELAY signal for Channel N.
DEVICE RESET
The ADATE207 has an internal PLL and FIFO that require reset
upon power up and changes to the MCLK input. The device has
three reset controls.
RESET_B input pin for hard resets.
CPU writeable control bit (Bit 00 in Register 0x19) for soft
resets.
CPU writeable control bit (Bit 03 in Register 0x19) to reset
errors and internal FIFOs.
MCLK
PER_EARLY_T0EN
INPUT_DELAY[7:0]
DELAY
05
55
7-
00
5
Figure 11. Timing Diagram for PER_EARLY_T0EN and INPUT_DELAY
相关PDF资料 |
PDF描述 |
|---|---|
| ADC0804LCN | IC ADC 8-BIT 10KSPS 1LSB 20-DIP |
| ADC0820CCM+ | IC ADC 8-BIT HS 20-SOIC |
| ADF4001BRU | IC CLOCK GEN PLL 16-TSSOP |
| ADF4002BRUZ-RL7 | IC PLL FREQUENCY SYNTH 16-TSSOP |
| ADF4007BCPZ-RL7 | IC DIVIDER/PLL SYNTHESZR 20LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADATE209 | 制造商:AD 制造商全称:Analog Devices 功能描述:4.0 Gbps Dual Driver |
| ADATE209BBCZ | 制造商:Analog Devices 功能描述:4.0 GBPS DUAL DRIVER - Rail/Tube |
| ADATE209BCPZ | 制造商:Analog Devices 功能描述: |
| ADATE302-02 | 制造商:AD 制造商全称:Analog Devices 功能描述:500 MHz Dual Integrated DCL with Differential Drive/Receive, Level Setting DACs, and Per Pin PMU |
| ADATE302-02BBCZ | 功能描述:IC DCL ATE 500MHZ DUAL 84CSPBGA RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
发布紧急采购，3分钟左右您将得到回复。