- 您现在的位置：买卖IC网 > PDF目录20622 > ADE7953ACPZ (Analog Devices Inc)IC ENERGY METERING 1PH 28LFCSP PDF资料下载
参数资料
| 型号： | ADE7953ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/72页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PH 28LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 660 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电流 - 电源： | 6.8mA |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADE7953
Active Energy Integration Time Under Steady Load
The discrete time sample period (T) for the accumulation
registers is 4.83 μs (1/206.9 kHz). With full-scale sinusoidal
signals on the analog inputs and the AWGAIN and BWGAIN
registers set to 0x400000, a pulse is generated and added to
the AENERGYA and AENERGYB registers every 4.83 μs.
The maximum positive value that can be stored in the 24-bit
AENERGYA and AENERGYB registers is 0x7FFFFF before
the register overflows. The integration time under these
conditions can be calculated as follows:
Data Sheet
Line cycle accumulation mode is disabled by default and can be
enabled on Current Channel A and Current Channel B by setting
the ALWATT and BLWATT bits to 1 in the LCYCMODE register
(Address 0x004). The accumulation time should be written to
the LINECYC register (Address 0x101) in the unit of number of
half line cycles. The ADE7953 can accumulate energy for up to
65,535 half line cycles. This equates to an accumulation period
of approximately 655 sec with 50 Hz inputs and 546 sec with
60 Hz inputs.
The number of half line cycles written to the LINECYC register
Time = 0x7FFFFF × 4.83 μs = 40.5 sec
Active Energy Line Cycle Accumulation Mode
(11)
is used for both the Current Channel A and Current Channel B
accumulation periods. At the end of a line cycle accumulation
cycle, the AENERGYA and AENERGYB registers are updated,
In active energy line cycle accumulation mode, the energy
accumulation of the ADE7953 is synchronized to the voltage
channel zero crossing so that the active energy can be accumu-
lated over an integral number of half line cycles. This feature is
available for both Current Channel A and Current Channel B
active energy. The advantage of summing the active energy over
an integral number of half line cycles is that the sinusoidal
component of the active energy is reduced to 0 (see Equation 12
to Equation 15). This eliminates any ripple in the energy calcula-
tion. Energy is calculated more accurately and in a shorter time
because the integration period can be shortened. The line cycle
accumulation mode can be used for fast calibration and also to
obtain the average power over a specified time period. Using
Equation 6, the following description of the energy accumulation
can be derived:
P(t) = VI – [ LPF ] × cos(2ω t) (12)
nT nT
E ( t ) ? ? VIdt ? [ LPF ] ? ? cos( 2 ωt ) dt (13)
0 0
where:
n is an integer.
T is the line cycle period.
Because the sinusoidal component is integrated over an integer
number of line cycles, its value is always 0. Therefore,
and the CYCEND flag is set in the IRQSTATA register (Address
0x22D and Address 0x32D). If the CYCEND bit in the IRQENA
register is set, an external interrupt is issued on the IRQ pin. In
this way, the IRQ pin can also be used to signal the completion of
the line cycle accumulation. Another accumulation cycle begins
immediately as long as the ALWATT and BLWATT bits in the
LCYCMODE register remain set.
The contents of the AENERGYA and AENERGYB registers are
updated synchronous to the CYCEND flag. The AENERGYA and
AENERGYB registers hold their current values until the end of
the next line cycle period, when the contents are replaced with
the new reading. If the read-with-reset bit (RSTREAD) in the
LCYCMODE register (Address 0x004) is set, the contents of the
AENERGYA and AENERGYB registers are cleared after a read
and remain at 0 until the end of the next line cycle period.
If a new value is written to the LINECYC register (Address 0x101)
midway through a line cycle accumulation, the new value is not
internally loaded until the end of a line cycle period. When the
LINECYC register is updated mid-reading, the current energy
accumulation cycle is completed, and the new value is then
programmed, ready for the next cycle. This prevents any invalid
E(t) ?
nT
? VIdt ?
0
(14)
AENERGYx REGISTER
0
E = VInt
(15)
CYCEND IRQ
LINECYC REGISTER
NEW LINE CYCLE
VALUE PROGRAMMED
INTERNAL LINE CYCLE
UPDATED
Figure 47. Changing the LINECYC Register
Rev. B | Page 26 of 72
相关PDF资料 |
PDF描述 |
|---|---|
| RS-2412DZ/H3 | CONV DC/DC 2W 9-36VIN +/-12VOUT |
| HMC12DTES | CONN EDGECARD 24POS .100 EYELET |
| HMC49DREF-S13 | CONN EDGECARD 98POS .100 EXTEND |
| ESC26DTEF | CONN EDGECARD 52POS .100 EYELET |
| AISC-0402-2N0J-T | INDUCTOR WW CERAM 2.0NH 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7953ACPZ-RL | 功能描述:IC ENERGY METERING 1PH 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7978ACPZ | 制造商:Analog Devices 功能描述: |
| ADE7978ACPZ-RL | 功能描述:3 Phase Meter IC 28-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 输入阻抗:280 千欧 测量误差:- 电压 - I/O 高:2.4V 电压 - I/O 低:0.8V 电流 - 电源:10.6mA 电压 - 电源:2.97 V ~ 3.63 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-WFQFN 裸露焊盘，CSP 供应商器件封装:28-LFCSP-WQ（5x5） 标准包装:5,000 |
| ADE8052-DWDL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE8052-EMUL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。