- 您现在的位置：买卖IC网 > PDF目录20622 > ADE7953ACPZ (Analog Devices Inc)IC ENERGY METERING 1PH 28LFCSP PDF资料下载
参数资料
| 型号： | ADE7953ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 55/72页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PH 28LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 660 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电流 - 电源： | 6.8mA |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Data Sheet
UART INTERFACE
Table 10. Frames in the UART Packet
ADE7953
The ADE7953 provides a simple universal asynchronous
receiver/transmitter (UART) interface that allows all the functions
of the ADE7953 to be accessed using only two single-direction
pins. The UART interface allows an isolated communication
Frame
F1
F2
F3
Function
Read/write
Address MSB
Address LSB
interface to be achieved using only two low cost opto-isolators.
The UART interface operates at a fixed baud rate of 4800 bps
and is therefore suitable for low speed designs.
The UART interface on the ADE7953 is accessed via the Tx pin
(Pin 26), which transmits data from the ADE7953 , and the Rx
pin (Pin 27), which receives data from the microcontroller. A
simple master/slave topology is implemented on the UART inter-
face with the ADE7953acting as the slave. All communication
is initiated by the sending of a valid frame by the master (the
microcontroller) to the slave (the ADE7953 ). The format of the
As shown in Figure 72, each frame consists of 10 bits. Each bit is
sent at a bit rate of 4800 bps, resulting in a frame time of 2.08 ms
((1/4800) × 10). A wait period of 6 ms should be added from
when the UART communication mode is established using the
CS and SCLK pins to when the first frame is sent. A minimum
wait of 0.2 ms should be included between frames. All frame
data is sent LSB first.
Communication via the UART interface is initiated by the
F1 determines whether the communication is a read or a write
operation, and the following two frames (F2 and F3) select the
register that is to be accessed. Each frame consists of eight data
bits, as shown in Figure 72. A read is issued by writing the value
0x35 to F1, and a write is issued by writing the value 0xCA to
F1. Any other value is interpreted as invalid and results in an
unsuccessful communication with the ADE7953 . The address
bytes are sent MSB first; therefore, F2 contains the most
significant portion of the address, and F3 contains the least
significant portion of the address. The bits within each address
frame are sent LSB first.
The ADE7953 UART interface uses two timeouts, t 1 and t 2 , to
synchronize the communication and to prevent the communi-
cation from halting. The first timeout, t 1 , is the frame-to-frame
delay and is fixed at 4 ms max. The second timeout, t 2 , is the
packet-to-packet delay and is fixed at 6 ms min. These two
timeouts act as a reset for the UART function. More informa-
tion about how the timeouts are implemented is provided in
the UART Read section and the UART Write section.
Verification of a successful UART communication can be
achieved by implementing a write/read/verify sequence in the
microcontroller. Successful communications are also recorded
in the LAST_ADD, LAST_RWDATA, and LAST_OP registers,
as described in the Communication Verification section.
t 2
SCLK
CS
t 1
Rx
FRAME
t 1 = FRAME DELAY: 0.2ms (MIN), 4ms (MAX)
t 2 = PACKET DELAY: 6ms (MIN)
Figure 72. UART Frame
Rev. B | Page 55 of 72
相关PDF资料 |
PDF描述 |
|---|---|
| RS-2412DZ/H3 | CONV DC/DC 2W 9-36VIN +/-12VOUT |
| HMC12DTES | CONN EDGECARD 24POS .100 EYELET |
| HMC49DREF-S13 | CONN EDGECARD 98POS .100 EXTEND |
| ESC26DTEF | CONN EDGECARD 52POS .100 EYELET |
| AISC-0402-2N0J-T | INDUCTOR WW CERAM 2.0NH 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7953ACPZ-RL | 功能描述:IC ENERGY METERING 1PH 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7978ACPZ | 制造商:Analog Devices 功能描述: |
| ADE7978ACPZ-RL | 功能描述:3 Phase Meter IC 28-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 输入阻抗:280 千欧 测量误差:- 电压 - I/O 高:2.4V 电压 - I/O 低:0.8V 电流 - 电源:10.6mA 电压 - 电源:2.97 V ~ 3.63 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-WFQFN 裸露焊盘，CSP 供应商器件封装:28-LFCSP-WQ（5x5） 标准包装:5,000 |
| ADE8052-DWDL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE8052-EMUL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。