- 您现在的位置：买卖IC网 > PDF目录20622 > ADE7953ACPZ (Analog Devices Inc)IC ENERGY METERING 1PH 28LFCSP PDF资料下载
参数资料
| 型号： | ADE7953ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 43/72页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PH 28LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 660 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电流 - 电源： | 6.8mA |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Data Sheet
ZERO-CROSSING DETECTION
The ADE7953 includes a zero-crossing (ZX) detection feature
on all three input channels. Zero-crossing detection allows
measurements to be synchronized to the frequency of the
incoming waveforms.
Zero-crossing detection is performed at the output of LPF1 to
ensure that no harmonics or distortion affect the accuracy of the
zero-crossing measurement. LPF1 is a single-pole filter with a
?3 dB cutoff of 80 Hz and is clocked at 223 kHz. The phase shift
of this filter therefore results in a time delay of approximately
2.2 ms (39.6°) at 50 Hz. To assure good resolution of the ZX
detection, LPF1 cannot be disabled. Figure 61 shows how the
zero-crossing signal is detected.
DSP
ADE7953
As shown in Figure 62, the ZX output pin goes high on the
positive-going edge of the voltage channel zero crossing and
low on the negative-going edge of the zero crossing. A delay
of approximately 2.2 ms should be expected on this pin due to
the time delay of LPF1.
Current Channel Zero Crossing
The current channel zero-crossing indicator is output on Pin 21
(ZX_I) by default. The ZX_I pin operates in a similar way to the
ZX pin (see Figure 62). The ZX_I pin goes high on the positive-
going edge of the current channel zero crossing and low on the
negative-going edge of the current channel zero crossing. By
default, the ZX_I pin is triggered based on Current Channel A.
The ZX_I pin can be configured to trigger based on Current
IA, IB,
OR V
REFERENCE
GAIN[23:0]
HPFEN BIT
ZX
Channel B by setting the ZX_I bit (Bit 11) of the CONFIG
register (Address 0x102) to 1.
DETECTION
PGA
ADC
HPF
LPF1
ZERO-CROSSING INTERRUPTS
Three interrupts are associated with zero-crossing detection, one
39.6° OR 2.2ms @ 50Hz
for each input channel: Current Channel A, Current Channel B,
and the voltage channel. The zero-crossing condition occurs
0V
ZX
ZX
ZX
ZX
when either a positive or a negative zero-crossing transition
takes place. If this transition occurs on the voltage channel, the
IA, IB, OR V
LPF1 OUTPUT
ZXV bit (Bit 15) of the IRQSTATA register (Address 0x22D and
Figure 61. Zero-Crossing Detection
The error in the ZX detection is 0.08° for 50 Hz systems and
0.09° for 60 Hz systems. The zero-crossing information is
available on both an output pin or via an interrupt.
ZERO-CROSSING OUTPUT PINS
By default, the voltage and current channel ZX information
is configured to be output on Pin 1 (ZX) and Pin 21 (ZX_I),
respectively. These dedicated output pins provide an unlatched
ZX indicator (see the Alternative Output Functions section).
Voltage Channel Zero Crossing
The voltage channel zero-crossing indicator is output on Pin 1
(ZX) by default. Figure 62 shows the operation of the ZX output.
V
2.2ms @ 50Hz
ZX
Figure 62. Voltage Channel ZX Output
Address 0x32D) is set to 1. If this transition occurs on Current
Channel A, the ZXIA bit (Bit 12) of the IRQSTATA register is
set to 1. If this transition occurs on Current Channel B, the
ZXIB bit (Bit 12) of the IRQSTATB register (Address 0x230 and
Address 0x330) is set to 1. Figure 63 shows the operation of the
voltage channel zero-crossing interrupt.
V
ZXV (BIT 15) OF
IRQSTATA REGISTER
Figure 63. Zero-Crossing Interrupt
As shown by the dotted line in Figure 63, the ADE7953 can be
configured to trigger a zero-crossing event on only the positive-
going or the negative-going zero crossing. The ZX_EDGE bits
(Bits[13:12]) of the CONFIG register (Address 0x102) set the
edge that triggers the zero-crossing event. These bits default to
00 (the zero-crossing event is triggered on both the positive-
going and negative-going edges). Changing the ZX_EDGE bits
affects the zero-crossing event on all three channels. Note that
changing the ZX_EDGE bits affects only the ZX status bits and
interrupts; the function of the ZX pin (Pin 1) and the ZX_I pin
(Pin 21) is not affected.
Rev. B | Page 43 of 72
相关PDF资料 |
PDF描述 |
|---|---|
| RS-2412DZ/H3 | CONV DC/DC 2W 9-36VIN +/-12VOUT |
| HMC12DTES | CONN EDGECARD 24POS .100 EYELET |
| HMC49DREF-S13 | CONN EDGECARD 98POS .100 EXTEND |
| ESC26DTEF | CONN EDGECARD 52POS .100 EYELET |
| AISC-0402-2N0J-T | INDUCTOR WW CERAM 2.0NH 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7953ACPZ-RL | 功能描述:IC ENERGY METERING 1PH 28LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7978ACPZ | 制造商:Analog Devices 功能描述: |
| ADE7978ACPZ-RL | 功能描述:3 Phase Meter IC 28-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 输入阻抗:280 千欧 测量误差:- 电压 - I/O 高:2.4V 电压 - I/O 低:0.8V 电流 - 电源:10.6mA 电压 - 电源:2.97 V ~ 3.63 V 表计类型:3 相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-WFQFN 裸露焊盘，CSP 供应商器件封装:28-LFCSP-WQ（5x5） 标准包装:5,000 |
| ADE8052-DWDL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE8052-EMUL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。