参数资料
| 型号： | ADM1067ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/32页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 10 |
| 输出： | 可编程 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 托盘 |
| 配用： | EVAL-ADM1067TQEBZ-ND - BOARD EVALUATION FOR ADM1067TQ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1067
INPUTS
SUPPLY SUPERVISION
The ADM1067 has 10 programmable inputs. Five of these are
dedicated supply fault detectors (SFDs). These dedicated inputs
are called VH and VPx (VP1 to VP4) by default. The other five
inputs are labeled VXx (VX1 to VX5) and have dual functionality.
They can be used either as SFDs, with functionality similar to VH
and VPx, or as CMOS-/TTL-compatible logic inputs to the device.
Therefore, the ADM1067 can have up to 10 analog inputs, a
minimum of five analog inputs and five digital inputs, or a combi-
nation thereof. If an input is used as an analog input, it cannot
be used as a digital input. Therefore, a configuration requiring
10 analog inputs has no available digital inputs. Table 6 shows
the details of each input.
PROGRAMMING THE SUPPLY FAULT DETECTORS
The ADM1067 can have up to 10 SFDs on its 10 input channels.
These highly programmable reset generators enable the supervision
of up to 10 supply voltages. The supplies can be as low as 0.573 V
and as high as 14.4 V. The inputs can be configured to detect
an undervoltage fault (the input voltage drops below a prepro-
grammed value), an overvoltage fault (the input voltage rises above
a preprogrammed value), or an out-of-window fault (the input
voltage is outside a preprogrammed range). The thresholds can be
programmed to an 8-bit resolution in registers provided in the
ADM1067. This translates to a voltage resolution that is
dependent on the range selected.
The threshold value required is given by
V T = ( V R × N )/255 + V B
where:
V T is the desired threshold voltage (undervoltage or overvoltage).
V R is the voltage range.
N is the decimal value of the 8-bit code.
V B is the bottom of the range.
Reversing the equation, the code for a desired threshold is given
by
N = 255 × ( V T ? V B )/ V R
For example, if the user wants to set a 5 V overvoltage threshold
on VP1, the code to be programmed in the PS1OVTH register
(as discussed in the AN-698 Application Note at www.analog.com )
is given by
N = 255 × (5 ? 2.5)/3.5
Therefore, N = 182 (1011 0110 or 0xB6).
INPUT COMPARATOR HYSTERESIS
The UV and OV comparators shown in Figure 19 are always
monitoring VPx. To avoid chatter (multiple transitions when the
input is very close to the set threshold level), these comparators
have digitally programmable hysteresis. The hysteresis can be
RANGE
SELECT
The resolution is given by
Step Size = T hreshold Range /255
Therefore, if the high range is selected on VH, the step size can
VPx
ULTRA
LOW
VREF
+
–
OV
COMPARATOR
GLITCH
FILTER
FAULT
OUTPUT
be calculated as follows:
(14.4 V ? 6.0 V)/255 = 32.9 mV
LOW
MID
+
–
UV
COMPARATOR
FAULT TYPE
SELECT
the bottom of each range (V B ), and the range itself (V R ).
Figure 19. Supply Fault Detector Block
Table 5. Voltage Range Limits
Voltage Range (V)
0.573 to 1.375
1.25 to 3.00
2.5 to 6.0
6.0 to 14.4
V B (V)
0.573
1.25
2.5
6.0
V R (V)
0.802
1.75
3.5
9.6
The hysteresis is added after a supply voltage goes out of
tolerance. Therefore, the user can program the amount above
the undervoltage threshold to which the input must rise before an
undervoltage fault is deasserted. Similarly, the user can program
the amount below the overvoltage threshold to which an input
must fall before an overvoltage fault is deasserted.
Table 6. Input Functions, Thresholds, and Ranges
Input
VH
VPx
VXx
Function
High Voltage Analog Input
Positive Analog Input
High-Z Analog Input
Digital Input
Voltage Range (V)
2.5 to 6.0
6.0 to 14.4
0.573 to 1.375
1.25 to 3.00
2.5 to 6.0
0.573 to 1.375
0 to 5.0
Maximum Hysteresis
425 mV
1.02 V
97.5 mV
212 mV
425 mV
97.5 mV
N/A
Voltage Resolution (mV)
13.7
32.9
3.14
6.8
13.7
3.14
N/A
Glitch Filter (μs)
0 to 100
0 to 100
0 to 100
0 to 100
0 to 100
0 to 100
0 to 100
Rev. D | Page 15 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1068ASTZ-REEL7 | IC SEQUENCER/SUPERVISOR 32LQFP |
| ADM1069ACPZ-REEL7 | IC SUPERVISOR/SEQ PROG 40LFCSP |
| ADM1088AKS-REEL7 | IC SIMPLE SEQUENCER P-P SC70-6 |
| ADM1169ASTZ | IC SEQUENCER/SUPERVISOR 32LQFP |
| ADM1184ARMZ-REEL7 | IC VOLT MONITOR/SEQ 4CH 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1067ACPZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Super Sequencer with Open-Loop Margining DACs |
| ADM1067ASU | 功能描述:IC SUPERVISOR/SEQUENCER 48-TQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
| ADM1067ASU-REEL | 制造商:Analog Devices 功能描述:Sequencer 48-Pin TQFP T/R |
| ADM1067ASU-REEL7 | 制造商:Analog Devices 功能描述:Sequencer 48-Pin TQFP T/R |
| ADM1067ASUZ | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。